Consider two different machines, M1 and M2. M1 has a clock rate of 500 MHz and M2 has a clock rate of 750 MHz. The average instruction execution on M1 requires 4 cycles, while the ioaverage execution time on M2 requires 3 clock cycles. Which of the following statement is true? O Bis a faster than A by a factor of 500/750 O Bis faster than A by a factor of 2 O A is faster than B by a factor of 750/500 O Bil faster than A by a factor of 4/3

Consider two different machines, M1 and M2. M1 has a clock rate of 500 MHz and M2 has a clock rate of 750 MHz. The average instruction execution on M1 requires 4 cycles, while the ioaverage execution time on M2 requires 3 clock cycles. Which of the following statement is true? O Bis a faster than A by a factor of 500/750 O Bis faster than A by a factor of 2 O A is faster than B by a factor of 750/500 O Bil faster than A by a factor of 4/3

Database System Concepts

7th Edition

ISBN:9780078022159

Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Publisher:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Chapter1: Introduction

Section: Chapter Questions

Problem 1PE

See similar textbooks

Similar questions

A processor uses a serial link to communicate with a keyboard for word processing. A typist using this keyboard can type at rates peaking at 120 words per minute, where a word is 6 characters (including spaces and punctuation). The characters will be transmitted from the keyboard in 8-bit ASCII with one stop bit and no parity. Only consider these and no special characters. The programmer writes setup and polling service routines based on a minimum baud rate, but then finds that the keyboard will only interface at 19.2 Kbaud. Will the polling service routine have to change? Why or why not? Baud Rates 300 600 1200 2400 4800 9600 19200
Computer Science
dont copy from any existing answer diretly for sure i will downvote dont post without knowledge
5. We have a serial program with two parts A, and B such that: Executed time for A =4 s Executed time for B =2 s If part B is made to run four times faster, then calculate the speedup using Amdahl's law
Consider the following instructions for i - x to x+3 do v - i for j - 1 to y do V - v*i end for print v end for [NOTE:The statement i+ X replaces the old value of the variable i with the result of evaluating the expression x. For example, if i initially contains 7 then the statement i +x+1 results in i containing 8.] Which of the following cannot be produced by the instructions for any value of x? 64 125 216 343 8 27 64 125 27 64 125 216 9 16 25 36 9 27 81 243
VDHL simple computer question.
#ammend this code for the inputs (x = 5.01, 4.99, 0, -2.01, -1.99) so that there is a tolerance/Leeway for the values off > #such that 4.99 prints blue and -2.01 prints orange. # cannot adjust the value to x > 4.99 instead of 5 must add new code to add a tolerance or Leeway if x > 5: print ("blue") elif x < -2: print ("orange") else: print("purple")
The suitable instruction for mathematical expression S, cos-"(2x) Vavi int(acos(2*x)*sqrt(exp(pi/2),4,-6) int(acos(2x)*sqrt(exp(pi/2),-6,4) O int(acos(2*x)*sqrt(exp(pi/2),-6,4) O int(cosh(2*x)*sqrt(exp(pi/2),-6,4)
Write content of the register AL as two hexadecimal digits (without any other symbols). Image:
1. Write a Verilog code to design a clock with period = 100 ns and a duty cycle of 35% by using always and initial statements. The value of clock at time O should be initialized to 0.
E In the following code block(Reference:Q11), you will a set of assembly instructions with corresponding line numbers (line numbers are for informational purpose only and they are not part of the source code). 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 mov edx, 5 dec ecx jmp LABEL1 mov eax, 1 LABEL1: mul edx jmp ecx mov edx, 0678h sub edx, eax jmp DWORD PTR [edx] neg ebx add ecx, ebx mov eax, 0 For each of the conditions/scenario listed below, indicate the corresponding line number (that cause or is associated with the condition/scenario). Enter 0 (Zero) if the condition is not caused by the block of code. 1) Memory indirect jump: type your answer... type your answer... type your answer... type your answer... 2) Register indirect jump: 3) Relative short jump: type your answer... 5) Two's complement type your answer... 4) Relative near jump: 6) Unreachable code
Please refer to this textbook: “A. Silberschatz, P. B. Galvin and G. Gagne, “Operating System Principles,”7th Edition, John Wiley & Sons Inc., 2006.” And answer the following questions: Question:The Ricart& Argwala mutual exclusion algorithm: (a) Does not depend on time stamps in messages while Lamport's does. (b) Cannot handle the case where two or more processes request the same resource at the same time. (c) Does not require a process to send messages to the entire group while Lamport's does. (d) Requires fewer messages than Lamport's algorithm.