Consider thes ventory status of some system Demand=norm(u35,0%3D3) items/day IP OH Time order 10 days placed 1 2 3 4 months Time order recieved If the safety stock is 30, then Tis: O 40 O 230 O 30 O 260 ト Quantity

Q: 14. The operational amplifier circuit shown in the following figure includes a thermistor. V+ 6 100…

A: As per the Bartleby answering guidelines we are supposed to answer only first Question.please repost…

Q: Excessive delays have recently been noted on NewYork City’s 911 system. Discuss how you would…

A: The 911 emergency number system of New York City is a multi-server queuing model where multi-server…

Q: Ke'd TS+1 Considering a change in inlet temperature show why a 1st order model for a CSTR and a dead…

A: Given in Question :- R=radius K= conductivity  C= specific heat

Q: Consider a simple supported beam subjected to the load shown. The beam has a solid circular…

A: Bending moment A bending moment is a measure of the bending effect that can occur when an external…

Q: Discuss why the τbrake value always larger compare to the τnet.

A:

Q: Data for the Tesla Model 3 shown in figure 1 are given in the table below. Figure 1: Tesla Model 3…

A:

Q: A Carnot cyde, shown in Fig. (3) has the following condilions: V, = 7.5 L V, = 15 L, TH - 470o °C,…

A: Given data:- Volume at A, VA=7.5L=7.5×10-3m3Volume at B, VB=15L=15×10-3m3Higher temperature,…

Q: For a pressure to voltage sensor, when 500 bar is applied the coherent output voltage being Svolts,…

A: For a pressure to voltage sensor, when 500 bar is applied the coherent output voltage being Svolts.…

Q: The displacement of the system shown below must be limited to 50 inches, measured from th static…

A: Given data as per question F = 100 Sin(wt) K = 112.5 lb/in m = .50 lb-sec²/in w = 15 rad/sec The…

Q: Heat flow = AT × Area x Btu per hour %3D R-value (a) A stock-flow diagram, where the stock is the…

A: Part (a) Generally, we consider heat inflow as positive and heat outflow as negative for a system.…

Q: 1) Compute the reliability of the bridge system as shown in Figure 1. If the component reliability…

A: When components are in series,

Q: what is Bi in this problem explain?

A: Here Bi is the Biot number.

Q: 3- In the event of a malfunction in the engine temperature sensor, how will it affect the operation…

A: Given :-  In the event of a malfunction in the engine temperature sensor, how will it affect the…

Q: Engineering MechanCE A - Lopy Copy (Campatibity ModelF Word (Product Activation iailed) INSTRT…

A:

Q: QUESTION 1: DYNAMICS 1.1 Define the following terms: 1.1.1 1.1.2 Distance and give its Sl-unit…

A: “Since you have asked multiple question, we will solve the first question for you. If you want any…

Q: capacity is the maximum output rate that can be achieved by a facility under ideal conditions.…

A:

Q: of each resistance 96) Three identical coils , 102 and inductance 42mH are conected in star to va…

A: It is given as a 3 phase supply and so line voltage is 415 V Phase voltage can be found by:…

Q: 1. Explain the functions of the following ladder logic: (a) What will happen to motor and light when…

A:

Q: In C.R.O experiment, the input R.M.S voltage is 8V.The voltage per division is 5V, with a total…

A:

Q: The logical expression for a fault tree is given by: S = [X U (Y n Z)] U[An (B U CU D)] (a)…

A: Given S=X U Y∩Z∪A∩B∪C∪D

Q: In figure below compute the net force exerted on the hemispherical shape located at the bottom of…

A:

Q: 3–15. A utility lift vehicle is shown in Figure P13.15. Determine the force required by the…

A: Given data as per the question Load on the lift vehicle =1200 N

Q: In type of test signal,the signal value will increase linearly for t>0.

A: In the control system, the major test signals are as follows: Impulse Ramp Step Sinusoidal

Q: explain the Factor of Safety ? include minimum and the max

A: Explain the Factor of Safety, which include the minimum and the maximum FOS.

Q: Force (g) 150 100 50 1 1.5 2 2.5 3 Time (sec) 3.5 st 4.5 5 5.5

A: The passive force is the lowest force . The active force is the highest  force. Stimulation…

Q: Study the below response which obtained from HVACexperiment to find the following: Setpoint Upper…

A: Given response

Q: 2. (a) What is the temperature of air molecules if their average kinetic energy is 61 meV? (b) A…

A:

Q: Model by mechanical circuit. 2L 3 Funny

A: Given                  Mass = m Spring constant = k               Length = L Find  Equation of…

Q: Design the network represents the following activities, then 1) Calculate TE, .². 2) Find the…

A: Given

Q: 04 In the following circuit has two node A and B, buy nodal analysis Determine: 1) The voltages of…

A:

Q: Which of the following systems is designed toreduce NOx and has little or no effect on overallengine…

A: Given Data : NOx

Q: In the following circuit has two node A and B, buy nodal analysis Determine: 2) The currents…

A:

Work and Heat Transfer

It is generally related to thermal engineering which tells about the use, creation, conversion and transfer of heat energy between the systems. It is also considered that to transfer heat from one source to another, transfer of masses is also required. There are various mechanisms by which, transfer of heat takes place i.e. thermal conduction, convection, radiation or by change of phase. All these mechanisms have their own specific features which sometimes occur simultaneously within the same system.