Consider the 13 kg motorcycle wheel shown in the figure. Assume it to be approximately a ring with an inner radius of 0.285 m and an outer radius of 0.325 m. The motorcycle is on its center stand, so that the wheel can spin freely. If the drive chain exerts a force of 2200 N at a radius of 4.95 cm, what is the angular acceleration of the wheel, in radians per square second? What is the tangential acceleration, in meters per square second, of a point on the outer edge of the tire? How long, in seconds, starting from rest, does it take to reach an angular velocity of 89.5 rad/s?

Consider the 13 kg motorcycle wheel shown in the figure. Assume it to be approximately a ring with an inner radius of 0.285 m and an outer radius of 0.325 m. The motorcycle is on its center stand, so that the wheel can spin freely. If the drive chain exerts a force of 2200 N at a radius of 4.95 cm, what is the angular acceleration of the wheel, in radians per square second? What is the tangential acceleration, in meters per square second, of a point on the outer edge of the tire? How long, in seconds, starting from rest, does it take to reach an angular velocity of 89.5 rad/s?

Similar questions

= (a) In the figure below, wheel A of radius TA B to wheel C of radius rc 10 cm is coupled by belt 25 cm. The angular speed of wheel A is increased from rest at a constant rate of 1.6 rad/s². Find the time needed for wheel C to reach an angular speed of 100 rev/min, assuming the belt does not slip. (Hint: If the belt does not slip, the linear speeds at the two rims must be equal.) TC B
You are designing a lathe motor, part of which consists of a uniform cylinder whose mass is 140 kg and whose radius is 0.50 m that is mounted so that it turns without friction on its axis, which is fixed. The cylinder is driven by a belt that wraps around its perimeter and exerts a constant torque. At t = 0, the cylinder's anqular velocity is zero. At t = 25 s, its angular speed is 550 rev/min. (a) What is the magnitude of the cylinder's angular momentum at t = 25 s? |kg-m2/s (b) At what rate is the angular momentum increasing? kg-m2/s2 (c) What is the magnitude of the torque acting on the cylinder? N-m (d) What is the magnitude of the frictional force acting on the rim of the cylinder? eBook
In the figure, wheel A of radiusra = 13.2 cm is coupled by belt B to wheel C of radius rc = 26.2 cm. The angular speed of wheel A is increased from rest at a constant rate of 1.17 rad/s². Find the time needed for wheel C to reach an angular speed of 142 rev/min, assuming the belt does not slip. (Hint: If the belt does not slip, the linear speeds at the two rims must be equal.) B Number i Units
An electric drill starts from rest and undergoes uniform angular acceleration for a period of 0.130 s until it turns at a rate of 2.35 x 10 rev/min. (a) What is the drill's angular acceleration (in rad/s)? (Enter the magnitude.) rad/s? (b) What is the angle (in radians) through which the drill rotates during this period? (Enter the magnitude.) rad
A 2-kg disk has a radius of 18 cm and rotates with an angular acceleration of 12 rad/s2about an axis through its center and perpendicular to the plane of the disk. Determine the tangential force at the rim of the disk.
A child (mass 20 kg) is at the edge of a spinning merry-go-round (approximated as a solid disk of mass 100 kg, radius 2 m). The child walks towards the center of the merry-go-round until he is halfway from the edge. What is the final angular speed of the merry-go-round if the initial angular speed is 10 rad/s?
In the figure, wheel A of radius rA = 8.29 cm is coupled by belt B to wheel C of radius rc = 25.3 cm. The angular speed of wheel A is increased from rest at a constant rate of 2.63 rad/s?. Find the time needed for wheel C to reach an angular speed of 66.1 rev/min, assuming the belt does not slip. (Hint: If the belt does not slip, the linear speeds at the two rims must be equal.) B Number i Units
The axle of a flywheel has a radius of 0.06 m. A force of 50 newton is applied tangentially to the axle. Calculate the angular acceleration in rad/s2 of the flywheel, if its moment of inertia is 4 kg-m2.
As shown in the figure below, wheel A has a radius of 10 cm and is attached by a belt to to wheel C which has a radius of 25 cm. The angular speed of wheel A is increased from rest at a constant rate of 1.1 rad/s2(α). Determine the the time needed for wheel C to reach an angular speed of 100 rev/min assuming the belt does not slip. The linear velocity of the belt must be the same so αArA=αCrC. The relationship between angular acceleration and angular speed is ω=αt. 2pi rad = 1 rev. Don't forget to convert to consistent units.
A 39.8 kg child stands on a spinning platform that has been well maintained (neglect friction in the axle). Initially the platform is spinning at 4.9 rev/s while the child's arms are extended outward (holding some weights). The child then pulls the weights back to close to their body. What is the final angular speed in rev/s of the platform? Assume that the child can be considered a cylinder with a diameter of 1.2 m, spinning along its center axis and the weights are point masses (2 kg each) that are initially 1.1 m away from the center of the child. Assume that the weights are at the outer edge of the "cylinder" (i.e., the child) in the final moment.
Consider a bicycle wheel to be a ring of radius 30 cm and mass 1.5 kg. Neglect the mass of the axle and sprocket. If a force of 25 N is applied tangentially to a sprocket of radius 4 cm for 6 s, what angular speed does the wheel achieve, assuming it rolls without slipping? Round to the nearest rad/s.
In the figure, wheel A of radiusrA = 13.9 cm is coupled by belt B to wheel C of radius rc = 24.4 cm. The angular speed of wheel A is increased from rest at a constant rate of 1.45 rad/s². Find the time needed for wheel C to reach an angular speed of 50.5 rev/min, assuming the belt does not slip. (Hint: If the belt does not slip, the linear speeds at the two rims must be equal.) Number i Units