Consider the modulus of elasticity of aluminum to be 10,000 lb / in2. Verify homogeneity in the units. An aluminum block of rectangular cross section is subjected to an axial compressive force, if the side measuring 1.5 in changes in length to 1.500132 in, determine the poisson's ratio and the new length of the side measuring 5 cm.

Q: 1. A 300mm long composite bar is constructed by bonding an alloy steel outer sleeve of outside…

A: The given information in the problem is shown in the following attached image:

Q: Compound axial member ABC has a uniform diameter of d-2.4 in. Segment (1) is an aluminum [E₁ -…

A:

Q: A support beam has a length of 75 cm, width 35 cm and 50 cm thickness. What is the weight which the…

A: Given Data⇒ Length of beam(L)=75 cm=0.75 m Width(W)=35 cm=0.35 m Thickness(t)=50 cm=0.50 m…

Q: . A sheet of plywood consists of three equally thick sheets, the upper and lower sheets having their…

A: Given   Tensile modulus, E1 = 10 GPa                              E2 = 0.4 GPa Find   Tensile…

Q: Two round rods, one of steel, the other of brass, are joined end to end. Each rod is 0.5 m long and…

A: Given that, Esteel=20×1010PaEbrass=10×1010Pa

Q: 20 KN 38 mm Ø | 1.0 m 40 KN 40 kN, B 64 mm 1.5.m C Fig.pl-01 P2. Solve Problem P1-01 if rod BC is a…

A: Given:Diameter of part AB, D1=38 mmOuter diameter of part BC, D2=64 mmInner diameter of part BC,…

Q: A sheet of plywood consists of three equally thick sheets, the upper and lower sheets having their…

A: Given   Tensile modulus, E1 = 10 GPa                              E2 = 0.4 GPa Find   Tensile…

Q: The original length of a piece of metal is 400 mm, this piece has pulled in tension with stress of…

A:

Q: A 30 cm long bar is 5cm square in section for 12 cm of its length of 2.5 cm diameter for 8 cm, and…

A:

Q: A tensile load of 50, 000 lb is applied to a metal bar with a 0.6 in x 0.6 in. cross section and a…

A:

Q: a 200mm long rod with a diameter of 50mm is loaded with a 4kN weight.the rod finale length 201.314mm…

A: Hello. Since your question has multiple sub-parts, we will solve first three sub-parts for you. If…

Q: A wire with a Young’s Modulus, E, of 8.5 x 106 N/m2 and an original length of 1.5 m is under…

A: Calculate the strain in the wire. ε=δll Here, l is the original length of the wire, δl is the change…

Q: A copper rod with a diameter of 19 mm, modulus of 110 GPa, and a Poisson’s ratio of 0.35 is…

A:

Q: A 8mm diameter rod, of unknown material, is subjected to 50kN tensile load. In the process, its…

A: GIVEN DATA Diameter d=8mm Load P=50KN Initial length =300mm final length = 303mm

Q: A metal block of cross-section area A and length L is subject to a tensile stress of S. The block…

A:

Q: Let's consider a rod having a solid circular cross-section with diameter of 5 mm and it is made of a…

A: Given:-  Diameter of rod: d =5 mm Young's modulus: E=120 GPa Poisson's ratio: μ=0.33 new diameter:…

Q: A square bar subjected to a tensile load of 100KN having a gauge length of 200mm, extends to a…

A:

Q: The bar shown in diagram is subjected to a tensile load of 150 kN. If the stress in the middle…

A: The tensile load F = 150 kN.The stress in the middle portion  (σ) = 160 N/mm2The total elongation of…

Q: A wire 10 m long has a cross-sectional area 1.25 x 10-4 m2. It is subjected to a load of 5 kg. If…

A:

Q: Question 3 Determine the elongation of the square hollow bar when it is subjected to the axial force…

A: Given Data: The load on the bar is P = 100 kN. The outer dimensions of the square cross-section is…

Q: If the Young’s modulus and rigidity modulus of a material are 210GPa and 70GPa respectively,…

A: We have given the following problem If the Young’s modulus and rigidity modulus of a material are…

Q: A specimen of magnesium having a rectan- gular cross section of dimensions 3.2 mm x 19.1 mm in.…

A: Given Load versus extension To find Data plotting Modulus of elasticity Yield strength at an offset…

Q: Compute the radius of relative stiffness of 20 cm thick cement concrete slab from the following…

A:

Q: Determine the elastic tensile load "F" that acts on mild steel specimen of Diameter 9 mm & Modulus…

A:

Q: The elongation of a bar of uniform cross section subjected to an axial force is given by the…

A: Elongation of the bar of uniform cross-section, δ=PLAE Here, δ is the elongation of the bar, P is…

Q: If the modulus of elasticity and modulus of rigidity values are 205 GPa and 80 GPa, then the value…

A: Modulus of elasticity = 205 gpa  Modulus of rigidity = 80 gpa  Find :-  Poisson ratio = ?

Q: Determine the elastic tensile load "F" that acts on mild steel specimen of Diameter 5 mm & Modulus…

A: Given:Diameter of specimen, D=5 mmModulus of elasticity, E=207 GPa=207*103 N/mm2Extension in…

Q: A vertebra is subjected to a shearing force of 590 N. Find the shear deformation (in m), taking the…

A:

Q: A steel Column is 10m long and Ø1.2m. It carries a load of 102MN. Given the modulus of Elasticity is…

A: Given Length of column 'l'=10mDiameter of column 'ϕ'=1.2mLoad carried of column 'P'=102MN…

Q: The femur, the long bone in the thigh, can be modeled as a tube of compact bone for most of its…

A: Given Data Cross sectional area of the bone is : A=4.8×10-4 m2 Mass of the person is : m=70 kg Now…

Q: A square bar subjected to a tensile load of 100KN having a gauge length of 200mm, extends to a…

A: tensile load (F) = 100 kN gauge length (L) = 200 mm deformed length (δl) = 0.19 mm tensile strength…

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.