Consider the hydraulic lifter shown where A1 = 3.2 in^2 and A2=9.1 in^2, and the applied force Fin=125 lbs. What is the output force F2? S1A₁FIN = F₁PISTON1P1OILA2FOUT = F₂PISTON2P2S2Consider the hydraulic lifter shown where A1 = 3.2 in^2 and A2=9.1 in^2, and the applied force Fin=125lbs. What is the output force F2?

Name: Consider the hydraulic lifter shown where A1 = 3.2 in^2 and A2=9.1 in^
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: Consider the hydraulic lifter shown where A1 = 3.2 in^2 and A2=9.1 in^2, and the applied force Fin=125 lbs. What is the output force F2? S1A₁FIN = F₁PISTON1P1OILA2FOUT = F₂PISTON2P2S2Consider the hydraulic lifter shown where A1 = 3.2 in^2 and A2=9.1

Answered: Consider the hydraulic lifter shown…

Engineering

Mechanical Engineering

Consider the hydraulic lifter shown where A1 = 3.2 in^2 and A2=9.1 in^2, and the applied force Fin=125 lbs. What is the output force F2?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The length of the smooth circular shaft with a solid cross-sectional area of 315nm2 is 1 meter. Instead of this shaft, it is desired to use an evacuated circular-section shaft with a wall thickness of 3 mm with the same length and weight. For these two cases, compare the angles of rotation that would occur if a moment M = 600 (N.m) was applied to the end of the shaft made of material G-80 GPa.
For the cart of figure, compute the force on the wheels caused by deflecting the jet and thecompression of the spring, if its stiffness is 1.6 kN/m.
Question 3: A Pelton turbine is a turbine working under atmospheric pressure and which rotates thanks to water hitting its blades (see figure). The operation of the Pelton turbine can be modeled using RTT. Formulate the expression quantifying the forces acting over one blade of the Pelton turbine. You need to consider that the blade moves at a velocity w and the water travels with a velocity v. The water flow and deflector has a diameter d and the flow rate is Q. Disregard gravity and viscosity forces. WATER 5 CA
The load carrying crane shown in the figurethe drum with its rope wound with one hydromotorare driven. Object A is slanted as the rope hugsIt moves up and down over the sled.The diameter of the drum on which the rope is wound is 300 mm.All hydraulic system until hydromotor30% of pressure losses in the components (efficiency 0.7)It will be taken. Thread of hydraulic gear pump in one round0.8 lt of oil dispensed from the cavitiesSince it isa. Calculate the flow of the pump (lt / min)b. Find the working pressure of the pump (bar)Load speed v = 0.6 m / sTensile force on the rope T = 10,000 NIt will be taken.
Head 10lbs mass 4' 10=8" material is elashe and E = 2X10 PS, 8' The Base is sniamly moved with the Velocity of 5 m/s Find the Velocity and Acceleration of Head دے
The front and side views of a centrifugal impeller are shown in the figure below. All symbols have their usual meanings. The outer radius of the impeller is r2 = 0.4 m and the blade height at the impeller outlet b2₂ = 0.03 m. The volume flow rate of water (density = 1000 kg/m³) through the impeller is 0.2 m³/s. The outlet blade angle 8₂ = 50 degrees and the impeller rotational speed w=1600 rpm. Assume negligible losses, and the design conditions of whirl-free and shock-free entry. The impeller torque is B₂F N-m. Front View 12 b2 |+| Side View
This course A centrifugal pump with the following impeller dimensions is used to pump oil. The pump is running at 2500 rpm. CHide blocks b2 Boz 72 The parameters of the impeller are as follows: 1= 8cm, b1= 4cm, B1= 20° r2= 18cm, b2= 3cm, B2= 25° Take g= 9.81 m/s2 The velocity triangles at the inlet and the outlet are as follows V2 W2 W1 V1 U2 U1 Determine the outlet radial velocity in (m/s) Choose.., + Determine the theoretical head in (m) Choose.. Determine the volumetric flow rate in m/s Choose. 42 128 AM ENG A/23/2021
Part A plz
20. A thrust of 30 kN along the axis of a shaft is taken by a pivot bearing consisting of the frustum of a cone. The outer and inner diameters are 200 mm and 100 mm and the semi-angle of the cone is 60°. The shaft speed is 200 rev/min 0-02. Assuming that the intensity of pressure is uniform over the surface of the bearing, find, from first principles (a) the magnitude of this pros- sure, in N/m²; (b) the power absorbed in friction. (U. Lond.) and (Ans.: 1.272 MN/m²; 1.13 kW)
The front and side views of a centrifugal impeller are shown in the figure below. All symbols have their usual meanings. The outer radius of the impeller is r2 = 0.4 m and the blade height the impeller outlet b₂ = 0.02 m. The volume flow rate of water (density = 1000 kg/m³) through the impeller is 0.5 m³/s. The outlet blade angle 3₂ = 35 degrees and the impeller rotational speed w=1600 rpm. Assume negligible losses, and the design conditions of whirl-free and shock-free entry. The gravitational acceleration g = 9.81 m/s². The theoretical (Euler) head is m. Front View P₂1 r2 b2- 118 Side View
Please don't provide handwritten solution. Draw the normal, transverse and bending moment diagrams for the structure represented in the figure. could be more specific in the balance equations for each effort
Question 3 A pipe of 150mm bore is delivering water at the rate of 7500 dm/min at a pressure of 820 kN/m?.It connects by a gradually expanding pipe to a main of 300 mm bore which runs 3m above it. Find the pressure in the 300mm main?