Consider the hollow pipe supported and loaded as shown below. Which of the following represents the bending moments at the cross-section containing points K and H? 700 mm Select one: O A. F and F O B. Mr and My O C. My and M₂ O D. Mr and Mz 40° 25 kN H 1,500 mm

Q: _____ is an example for indirect stress Select one: a. Shear b. Bending c. Tensile d. Compression

A:

Q: The efficiency of a power screw does nột depend on which of the following variables. Hint: Look at…

A: formula for efficiency of power screw is given byη=Fl2πThere F=load in newtonl=lead T=torquetorque…

Q: Cast iron is used to make rollers as it has superior compression load. Select one: True False

A: Solution:

Q: important property of many tool steals, is the ability of a tool steel to retain its mechanical and…

A: Yes, it is true.

Q: Fixing a wheel barrow takes a specific diameter axel of 2.50 inches. Thankfully, the manufacture…

A: It is given that the axle required for fixing the wheel barrow should have a diameter of 2.50…

Q: Compare the bolt patterns in shear shown below. The distance from the load to the centroid is the…

A: following is the answer and explanation for the above question-

Q: Cast iron is used to make rollers as it has superior compression load. Select one: True False

A: The above statement is false.

Q: Question 4 ( For the specimen shown, what will be the maximum stress near the hole region (in ksi)?…

A: Given:w=2.49 int=0.25 ind=1 inN=3350 lb NOTE: According to Bartleyby's guidelines we can answer only…

Q: Describe the concept of finding toughness using impact testing machine.

A:

Q: Generally, the Poisson's ratio of steel is

A: Poisson ratio of steel = 0.3 Option (c) is correct.

Q: 5- Which of the following material can be used to produce Tools a. Glasses b. Elastomers c. High…

A:

Q: Why it is important to loosen one screw before tightening the opposing one by an equal amount?

A: If there are two sequences of screws or bolts and n number of screws is to be tightened on each…

Q: Which one of the following material has the sheet metal applications O a. Mild steel O b. Cast iron…

A: Sheet metal is metal forming process which is used for forming into sheets

Q: What is the Flexure Formula?

A: The stresses in the beam caused by the bending moment is called as flexural or bending stress.

Q: Why should stress not exceed the material by design?

A: Every component is designed based on working stress which will acts on the component during its…

Q: Question 2: How long a wrench is needed to tighten a 9/16-inch bolt if the maximum force (pull) that…

A: Given: The diameter of bolt, d = 9/16 in = 0.5625 in The maximum force produced by mechanic, F = 75…

Q: A 25 ft long solid steel rod is subjected to a load of 10,000 Ib. This load causes the rod to…

A: Data given -  L = 25 ft = 25 × 12 P = 10000 lb  ∆L = 0.477 in  E = 30 × 106  psi

Q: Name the 2 types of axial loading?

A: Two types of axial loading are tensile and compressive stress. Both kinds of stresses arise within…

Q: Indicate the limbs with numbers and the joints with letters on the mechanism whose kinematic diagram…

A:

Q: Q1- Compare between the ferrous and non-ferrous metals in terms of the strength, hardness, weight,…

A: Ferrous metals contain iron, and non-ferrous metals don't. That means each type of ferrous and…

Q: a visual inspection check and at least one test safely on components that have failed in service.…

A: Given:There are two components that failed: the M24 engine mounting bolt and the fan…

Q: What happens if the material is isotropic?

A: Materials have certain properties like homogeneity, showing isotropic behavior, etc. Isotropy is…

Q: What will be the length of given mild steel rod after applying 100 kips force/load ?. If the…

A: Given, Force applied = P = 100 kips = 100 x 103 lb Diameter of rod = d = 0.5 in Length of rod = L =…

Q: Quenching is a process that can reduce the grain size and form a lot of grain boundaries in the…

A: Quenching: In this process metal is heated above its recrystallization and than cool it rapidly. The…

Q: High tensile strength materials are cut by a single point cutting too with the negative rake angle

A: Yes ,High tensile strength materials are cut by a single point cutting too with the negative rake…

Q: hich one of the following Cast iron is produced by the heat treatment of White cast iron?

A: 1)   Option b) Malleable   cast iron Malleable  cast  iron are relatively very soft and can…

Q: In the hardness test, answer the questions 1- What happens to the sample if its thickness is less…

A: Thickness of the specimen should be at least seven times of the depth of the indentation. It allows…

Q: High tensile strength materials are cut by a single point cutting too with the negative rake angle.…

A: Negative take is angle is used

Q: Sketch and explain any four Shaper operations?

A: The four shaper operations are, Horizontal cutting: It's one of the most popular operations on a…

Q: What is the point called when a material fractures?

A: The point at which material fractures is called the point of fracture or fracture point. In other…

Q: Define how to calculate the central angle of sliding slope in case of friction circle method?

A: A friction circle is a graphical tool that conveniently defines the course of action of the…

Q: Define the term Angle of Twist?

A: Whenever a twisting moment is applied on the shaft, the shaft's cross-section tends to rotate or…

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.