Consider the following circuit : Vcc RC R1 Cc R2 RE You are required to determine IBo using the following parameters : R = 22k0 R = 6kQ Rc = 2.6kQ RE = 1.3kQ Vcc = 22 V B = 183 %3D Firstly determine the Thevenin voltage source (in V) of the base circuit. Answer:

Q: What is the main difference between a BJT and a FET? a. both are three pin device b. BJT is a…

A: Different loads require different specifications to work. Analog devices are used for delivering…

Q: 1. Simulate the scenario shown in Figure 1.4 given in the above sections. Hint: continuous signals…

A: Given two sine signals with frequencies 40 and 90Hz Asked to sample and plot  the given signals at…

Q: QI Define lcno and leao. How are they different? How are they related? Are they typically close in…

A:

Q: ii. Thermocouple type K is used in measuring the temperature of the wastewater treatment as respect…

A: “Since you have asked multiple questions, we will solve the first question for you. If youwant any…

Q: Convert hexadecimal to octadecimal A13C

A: Conversion from hexa to octal is not direct, there is steps need to be followed, such as: Change…

Q: Number of minority charge carriers in an extrinsic semico a. Increase in temperature b. Increase in…

A: Extrinsic semiconductor: The extrinsic semiconductor is formed by doping the intrinsic semiconductor…

Q: What is the value of frequency of dc

A: The number of times a repeated event occurs per unit of time is known as frequency.  It's also…

Q: Draw 1.5 cycles of the analog signal and show the location and the value of each sample. [Q1] A…

A: Given a sinusoidal signal having, Frequency, f = 800 Hz                   T=1f=1800 Hz=1.25 ms…

Q: H3. (Dynamical System ) Explain various types of oscillator in non linear system

A: Nonlinear oscillator : Whenever a force is exerted on any particle then there is movement in the…

Q: Energy gap is overlapped between Valence band and Conduction band in O a. Insulators O b.…

A:

Q: Q) A CRO can be used to measure--- O A.C voltage. O D.C voltage. O Frequency. O All of above.

A: CRO displays the waveform on its screen.

Q: Write a technical report on Darlington Pair, which include the following topics: a) Technical…

A: Since it is asked to solve from sub-part (a) to (c), so we are solving only the first three…

Q: If the ammeter parameters due to insertion include 1200 internal resistance and a load resistance of…

A: Given, Internal resistance, Rint=120 Ω Load resistance, RL=2 kΩ Let the source voltage is V

Q: Draw What is the cross over distortion in class B?

A:

Q: With the given circuit below, if the input voltage is 10 volts peak-to-peak and the diode is…

A: The diode is ON when the voltage across anode is more than the cathode voltage. It is known as…

Q: How to find a mathematical model, called a state-space representation, for a linear time invariant…

A: State-space representation A mathematical model of a physical system as a set of input, output, and…

Q: After quantization, the analog signal has Select one: a. finite amplitudes O b. infinite amplitudes…

A: After quantization, the analog signal has  a. finite amplitudes b. infinite amplitudes c. finite…

Q: 1. Can the given. oscillation Circuit oscillate, if so find Wo. B₂ + and the condition fo

A: According to the question, we need to explain the given circuit.

Q: O 0.3 O 0.5 O 0.7 O 0.9 O 1.1 O 1.3 O 1.5 O 1.7

A: Answer: t = 0.5 seconds

Q: What happens to cut-in voltage when the temperature increases? a) Cut-in voltage increases b) Cut-in…

A: Option :b ( correct answer)

Q: justify balance modulators are used as mixers

A: The balanced  modulator or a mixer uses the  four-port hybrid junction that is shown below. The LO…

Q: Q4 Compare between Vametcan and Vazractca Vure = Vaameoretica V12 tractca)

A: Resistors, inductors and capacitors form an integral part of any electrical circuit. A source,…

Q: Perform the (v1-v2)/3 operation using an opamp.

A:

Q: Choose the correct mode of operation for each MOS band diagram below. Vacuum level Vacuum level En…

A: We need to choose the correct mode of operation for each Mos band diagram.

Q: A transistor is used as a switch and the waveforms are shown below. The parameters are given as…

A: Given  Transistor as switch and waveforms as shown  Vcc=200 vVCE(sat)=1 vICS=100 AICEO=1 mArise time…

Q: What are the analogue instruments in aircraft

A: Generally to indicate the location and the weather and the direction and the degree of aeroplane…

Q: Explain voltage and frequency operating limits

A: To move a charge from position to another position in an electric field a force, this force is…

Q: n ideal operational amplifier circuit in the closed-loop negative-feedback configuration is shown in…

A:

Q: Horizontal Controls Autoset tical Controls Trigger Controls

A:

Q: Stylus Film Substrate Stage Profile Signal Film Thickness Figure 8 Profilometer is one of the…

A: Profilometer is one f the important characterization equipment to determine the thickness of metal…

Q: Please validate the saturation assumption

A:

Q: HW14/ H.W: control the intensity of the LED by serial.

A: We required the following elements for the following to control the LED Arduino Board Led Arduino…

Q: explain in detail the static and dynamic characteristics of instruments

A: To choose the one most suited to a particular measurement application, we have to know the system…

Q: Explain dual slope ADC and successive approximation ADC with neat block diagram and compare the two…

A: The dual-slope ADC mainly consists of 5 blocks: Integrator, Comparator, Clock signal generator,…