Consider the following circuit diagram: 16 Ω 25j 64 Ω 400Z0° + -36j ZL Find Thevenin voltage V Th, Norton current IN, and maximum average power. (A) 12.2708-65.86°, 334.81/-5.13° and 12.27 W (B) 12.2708-65.86°, 334.81-5.13° and 1050.48 W (C) 334.81-5.13°, 12.2708-65.86° and 1050.48 W (D) 334.81/5.13°, 12.2708/65.86° and 12.27 W

Consider the following circuit diagram: 16 Ω 25j 64 Ω 400Z0° + -36j ZL Find Thevenin voltage V Th, Norton current IN, and maximum average power. (A) 12.2708-65.86°, 334.81/-5.13° and 12.27 W (B) 12.2708-65.86°, 334.81-5.13° and 1050.48 W (C) 334.81-5.13°, 12.2708-65.86° and 1050.48 W (D) 334.81/5.13°, 12.2708/65.86° and 12.27 W

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.14MCQ: The instantaneous power absorbed by the load in a single-phase ac circuit, for a general R LC load...

See similar textbooks

Similar questions

The instantaneous power absorbed by the load in a single-phase ac circuit, for a general R LC load under sinusoidal-steady-state excitation. is (a) Nonzero constant (b) Zero (c) Containing double-frequency components
A 220 Ω resistor is in series with an 80 mH inductor. The AC source is 48 at 1 kHz. The power factor is ________. Hint: Draw the circuit and get Vs and Is
Given the following circuit. What impedance load connected betweenterminals A and B will result in the maximum active power being delivered to the connected load?
Prob. I and Vc For the following RMS phasor circuit, a coworker has determined values for 50 Ohms 50 Ohms i,- 225 2253.13° = 190.92 + 254.56 VRMS R1 + R2 Vc = 237.17/26.565° = 212.13+ 106.07 VRMS 100 2 -3Z98.13° =-0.4243 + J2.970 ARMS C -j60 Ohms For this problem provide at least 3 digits of precision for the answers. The results for the following calculations are to be answered in - a) Find the current I b) Determine the real (P) and reactive(Q) power DELIVERED by the source c) Determine the real (P) and reactive (Q) power ABSORBED by each impedance ( resistors R1 and R2, inductor and capacitor). The values for P and Q can be positive or negative. Remember S =P+jQ, so do not include the j with your answer for Q. Each of these answers will require two parts. For the phasor a magnitude and angle will be needed. For the powers, The real power P and the reactive power Q are required.
"If lab is equal to 595.8252306 and lb is 344296, the phase sequence is:" O POSITIVE O NEGATIVE
Relative to the reference sinusoid, what is the phase angle of i, vR and vL in degrees?
Do aprr c ,d and e
A load is rated at 440V(rms), 7.5A(rms) and 3.3KW when connected to a 50HZ source. Find the load impedance.
Please do not copy other Platforms like Chegg or any. Please Solve without palgrism. I give upvote.
ans: a. i = 10 cis-30° Ab. v = 220 cis25° Vc. I = 7.0711 cis-30° Ad. V = 155.5635cis25° Ve. Z = 22 cis55° Ω
Shown in the figure below is an "RC" circuit drive by an AC power source. The AC power source has an RMS voltage of Vps (RMS) = 9.09 Volts and is running at a frequency of f = 1.138e+04 Hz. The resistor has a resistance of R = 2100 and the capacitor has an capacitance of C = 5.84e-09 Farads. Vps R ww с
Shown in the figure below is an "RC" circuit drive by an AC power source. The AC power source has an RMS voltage of Vps (RMS) = 11.58 Volts and is running at a frequency of f = 1.326e+04 Hz. resistor has a resistance of R = 3750 2 and the capacitor has an capacitance of C = 3.17e-09 Farads. Vps R ww Write the FORMULA for the total impedance of the circuit Ztot = Write the FORMULA for the phase of the total impedance of the circuit tot = Determine the numerical value of Ztot = Determine the numerical value of Pztot= Determine the current through the circuit: • I(PEAK) = • I(RMS) = Determine the voltage across the resistor: Amps Amps S2 C degrees