Formulas:Transmission delay= Length of packet in bits / Transmission ratePropagation delay = distance between two nodes / 3 x 108 m/sTotal delay at each link= Transmission delay + Propagation delay. Consider the figure below, with three links, each with the specified transmission rate and link length.+Link 1+Link 2+Link 3+Transmission rate: 1000 MbpsLink Length: 1 KmTransmission rate: 10 MbpsLink Length: 2 KmTransmission rate: 100 MbpsLink Length: 5000 KmAssume a packet length of 8000 bits is transmitted from host to destination.1. Find the delay on each link for one packet.2. Find the end to end (host to destination) delay for one packetConsider transmission delays and propagation delays but ignoring queuing delays and processing delays.

Total delay = Sum of transmission delay and propagation delay for each link Transmission delay =…

Consider the figure below, with three links, each with the specified transmission rate and link length. Link 1 Link 2 Link 3+ Transmission rate: 1000 Mbps Link Length: 1 Km Transnission rate: 10 Mbps Link Length: 2 Km Transmission rate: 100 Mbps Link Length: 5000 Km Assume a packet length of 8000 bits is transmitted from host to destination. 1. Find the delay on each link for one packet. 2. Find the end to end (host to destination) delay for one packet Consider transmission delays and propagation delays but ignoring queuing delays and processing delays.

Consider the figure below, with three links, each with the specified transmission rate and link length. Link 1 Link 2 Link 3+ Transmission rate: 1000 Mbps Link Length: 1 Km Transnission rate: 10 Mbps Link Length: 2 Km Transmission rate: 100 Mbps Link Length: 5000 Km Assume a packet length of 8000 bits is transmitted from host to destination. 1. Find the delay on each link for one packet. 2. Find the end to end (host to destination) delay for one packet Consider transmission delays and propagation delays but ignoring queuing delays and processing delays.

Database System Concepts

7th Edition

ISBN:9780078022159

Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Publisher:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Chapter1: Introduction

Section: Chapter Questions

Problem 1PE

See similar textbooks

Similar questions

Host A and B are directly connected by an 8mps link. The distance between the two host is 4000 kilometers. The propagation speed over the link is 2 x 10^8 m/s, and all packets are 1000 bytes long. What is the propagation delay, in seconds, between the two hots? What is the transmission delay, in seconds, between the two host?
1) Why both transport layer and link layers implement reliability mechanism .Please prove your answer by provide mathematical model of the required number of transmission over n hops. 2).Assume all the links from a source towards the destination provide reliable delivery service. Do we need TCP in the transport layer ?
Question 4 1 Point In circuit switching the packet queuing at the router level is due to the different links transmission rate. True B) False
Determine the respective summarized route of routers Rl and R2, to the Internet, with the longest possible network prefix.
Alert dont submit AI generated answer.
Calculate the delay x bandwidth product for the following links. Use one-way delay, measured from first bit sent to first bit received. (a) 100-Mbps Ethernet with a delay of 10 μs. (b) 100-Mbps Ethernet with a single store-and-forward switch like that of Exercise 16(b), packet size of 12,000 bits, and 10 μs per link propagation delay. (c) 1.5-Mbps T1 link, with a transcontinental one-way delay of 50 ms. (d) 1.5-Mbps T1 link between two groundstations communicating via a satellite in geosynchronous orbit, 35,900 km high. The only delay is speed-of-light propagation delay from Earth to the satellite and back.
Assume a 4Kbps link has a one-way latency of 50ms and a frame with 4-bit sequence numbers. Let the minimum frame size that can guarantee a 50% channel utilization assuming the stop-and-wait protocol is X' bits, and the minimum frame size that can guarantee a 50% channel utilization assuming the selective repeat protocol is 'Y' bits. Find the value of X+ Y?
1) Consider a reliable data transfer protocol that uses only negative acknowledgments. Suppose the sender sends data only infrequently. Would a NAK-only protocol be preferable to a protocol that uses ACKs? Why? 2) Besides network-related considerations such as delay, loss, and bandwidth performance, there are other important factors that go into designing a CDN server selection strategy. What are they? 3) What are the five layers in the Internet protocol stack? What are the principal responsibilities of each of these layers? List five tasks that a layer can perform. 4) Why do HTTP, SMTP, and POP3 run on top of TCP rather than on UDP? 5) List six access technologies. Classify each one as home access, enterprise access, or wide-area wireless access, and then describe how they fundamentally operate.
Consider the transmission of a packet from one end system to another. Each of the four categories of delays that a packet may encounter should be thoroughly described.
1. In this scenario, assume you are working on the link layer protocol using Stop-and-Wait ARQ data connection with a bandwidth of 500 Mbps to an oversea station in Taiwan. Assuming the station in Taiwan is 3057 km from the local station in Kuala Lumpur and the propagation speed is c= 2.2 x 10² m/s, answer the following: a) Calculate the bandwidth-delay product for communication between the two stations. b) Identify the utilization percentage of the link if the system data frames are 800 bits in length. c) Solve for the utilization percentage of the link if we have a protocol that can send up to 8 frames before stopping and worrying about the acknowledgments.
In step 4 of the CSMA/CA protocol, a station that successfully transmits a frame begins the CSMA/CA protocol for a second frame at step 2, rather than at step 1. What rationale might the designers of CSMA/CA have had in mind by having such a station not transmit the second frame. Immediately (if the channel is sensed idle)?