Consider the compound shaft KC which is composedof a 1200mm long solid rod fitted snuggly into anequally long pipe. Refer to the figure for givendimensions and material properties.If end K is fixed to a rigid wall and a concentratedtorque is applied at end C, determine the following:PipeE = 115 GPaG - 36.0 GPa1, = 48.0 MPa1200 mm180mm RodE = 220 GPaG = 85.0 GPa*, 80.0 MPa1. The required outer diameter for the pipe suchthat the rod and the pipe yields simultaneously.2. The corresponding maximum angle of twist ofthe shaft when it yields.3. The corresponding maximum torque T that canbe applied at end C of the shaft

Answered: Image /qna-images/answer/1b2053b3-763a-4cbd-a32f-ec52f8496d62.jpg

Consider the compound shaft KC which is composed of a 1200mm long solid rod fitted snuggly into an equally long pipe. Refer to the figure for given dimensions and material properties. If end K is fixed to a rigid wall and a concentrated torque is applied at end C, determine the following: Pipe E = 115 GPa G - 36.0 GPa 1,- 45.0 MPa 1200 mm 180mm Rod E = 220 GPa G = 85.0 GPa ,80.0 MPa 1. The required outer diameter for the pipe such that the rod and the pipe yields simultaneously. 2. The corresponding maximum angle of twist of the shaft when it yields. 3. The corresponding maximum torque T that can be applied at end C of the shaft

Consider the compound shaft KC which is composed of a 1200mm long solid rod fitted snuggly into an equally long pipe. Refer to the figure for given dimensions and material properties. If end K is fixed to a rigid wall and a concentrated torque is applied at end C, determine the following: Pipe E = 115 GPa G - 36.0 GPa 1,- 45.0 MPa 1200 mm 180mm Rod E = 220 GPa G = 85.0 GPa ,80.0 MPa 1. The required outer diameter for the pipe such that the rod and the pipe yields simultaneously. 2. The corresponding maximum angle of twist of the shaft when it yields. 3. The corresponding maximum torque T that can be applied at end C of the shaft

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.4.8P: Two sections of steel drill pipe, joined by bolted flange plates at Ä are being tested to assess the...

See similar textbooks

Similar questions

The hollow drill pipe for an oil well (sec figure) is 6,2 in. in outer diameter and 0.75 in. in thickness. Just above the bit, the compressive force in the pipe (due to the weight of the pipe) is 62 kips and the torque (due to drilling) is 185 kip-in. Determine the maximum tensile, compressive, and shear stresses in the drill pipe.
Solve the preceding problem for the following data: diameter LO m, thickness 48 mm, pressure 22 MPa, modulus 210 GPa. and Poisson's ratio 0.29
Solve the preceding problem for a W 200 × 41,7 shape with h = 166 mm, h = 205 mm. rw = 7.24 mm, tE= ILS mm,andV = 38 kN.
-15 Repeat the preceding problem using ??. = - 750 psi.
Repeat Problem 11.2-3 assuming that R= 10 kN · m/rad and L = 2 m.
Two sections of steel drill pipe, joined by bolted flange plates at Ä are being tested to assess the adequacy of both the pipes. In the test, the pipe structure is fixed at A, a concentrated torque of 500 kN - m is applied at x = 0.5 m, and uniformly distributed torque intensity t1= 250 kN m/m is applied on pipe BC. Both pipes have the same inner diameter = 200 mm. Pipe AB has thickness tAB=15 mm, while pipe BC has thickness TBC= 12 mm. Find the maximum shear stress and maximum twist of the pipe and their locations along the pipe. Assume G = 75 GPa.
Solve the preceding problem for the following data:P = 160 kN,JV = 200 tN,L = 2 m,b = 95 mm, h = 300 mm, and d = 200 mm
A plumber's valve wrench is used to replace valves in plumbing fixtures. A simplified model of the wrench (see figure part a) consists of pipe AB (length L. outer diameter D inner diameter dy), which is fixed at A and has holes of a diameter dhon either side of the pipe at B. A solid, cylindrical bar CBD (lengths, diameter^) is inserted into the holes at B and only one force F = 55 lb is applied in the -Z direction at C to loosen the fixture valve at A (see figure part c). Let G = 11,800 ksi, v = 0.30, L = 4 in., a = 4.5 in., d2= 1.25 in., dx= 1 in., and dh= 0.25 in. Find the state of plane stress on the top of the pipe near A (at coordinates A" = 0,Y = Q,Z = d->12), and show all stresses on a plane stress element (see figure part b). Compute the principal stresses and maximum shear stress, and show them on properly rotated stress elements
A torque T is applied to a thin-walled tube having a cross section in the shape of a regular hexagon with constant wall thickness t and side length b (see figure). Obtain formulas for the shear stress rand the rate of twist
Repeat Problem 11.3-9. Use two C 150 × 12.2 steel shapes and assume that E = 205 GPa and L = 6 m.
A motor driving a solid circular steel shaft with diameter d = 1.5 in, transmits 50 hp to a gear at B, The allowable shear stress in the steel is 6000 psi. Calculate the required speed of rotation (number of revolutions per minute) so that the shear stress in the shaft does not exceed the allowable limit.
Compare the angle of twist 1 for a thin-walled circular tube (see figure) calculated from the approximate theory for thin-walled bars with the angle of twist 2 calculated from the exact theory of torsion for circular bars, Express the ratio 12terms of the non-dimensional ratio ß = r/t. Calculate the ratio of angles of twist for ß = 5, 10, and 20. What conclusion about the accuracy of the approximate theory do you draw from these results?