Consider the compound shaft KC which is composedof a 1200mm long solid rod fitted snuggly into anequally long pipe. Refer to the figure for givendimensions and material properties.If end K is fixed to a rigid wall and a concentratedtorque is applied at end C, determine the following:PipeE115 GPaG = 36.0 GPa48.0 MPaTy1200 mmø180mm RodE = 220 GPaG85.0 GPa80.0 MPa1. The required outer diameter for the pipe suchthat the rod and the pipe yields simultaneously.2. The corresponding maximum angle of twist ofthe shaft when it yields.3. The corresponding maximum torque T that canbe applied at end C of the shaft

Answered: Image /qna-images/answer/4e64ecf1-35d2-43ad-bcb1-6b0f43931624.jpg

Consider the compound shaft KC which is compose of a 1200mm long solid rod fitted snuggly into an equally long pipe. Refer to the figure for given dimensions and material properties. If end K is fixed to a rigid wall and a concentrated torque is applied at end C, determine the following: Pipe E = 115 GPa G 36.0 GPa = 48.0 MPa 1200 mm ø180mm E = 220 G = 85.0 T = 80.0 1. The required outer diameter for the pipe suc that the rod and the pipe yields simultaneous 2. The corresponding maximum angle of twist c the shaft when it yields. 3. The corresponding maximum torque T that o be applied at end C of the shaft

Consider the compound shaft KC which is compose of a 1200mm long solid rod fitted snuggly into an equally long pipe. Refer to the figure for given dimensions and material properties. If end K is fixed to a rigid wall and a concentrated torque is applied at end C, determine the following: Pipe E = 115 GPa G 36.0 GPa = 48.0 MPa 1200 mm ø180mm E = 220 G = 85.0 T = 80.0 1. The required outer diameter for the pipe suc that the rod and the pipe yields simultaneous 2. The corresponding maximum angle of twist c the shaft when it yields. 3. The corresponding maximum torque T that o be applied at end C of the shaft

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: Q.I: A shaft composed of segments AB, BC is fixed between the two walls at A and C and loaded as…

Q: A simple torsion-bar spring is shown. The shear stress in the steel [G= 11,500 ksi] shaft is not to…

Q: 3.84 ksi

A: Calculating the axial stress (σ_axial):The axial stress is calculated by dividing the axial load (P)…

Q: The device serves as a compact torsional spring. It is made of A-36 steel and consists of a solid…

A: LAC=12 inLAB=12 inT=1.4 Kip. inr=0.5 inro= 1 inri=0.75 in find out :angle twist at C

Q: A solid shaft made of aluminum alloy (E=70 Gpa, v=0.33). The diameter of the shaft is 25 mm, and…

A: Introduction The strain represents the change in dimension of the body under the loading compared to…

Q: A 0.5 m-long metal composite shaft AB consists of a steel rod (radius r=25 mm), the outer surface of…

A: Answer and explanation are given below.Explanation: Please let me know if there are any further…

Q: The copper pipe (G= 50 GPa) is tightly secured to the wall at A, has an outer diameter of 40 mm and…

A: The objective of the question is to determine the maximum shear stress developed in the copper pipe…

Q: A torque of magnitude T= 25,000 lb-in is applied to the end of a tank containing compressed air…

Q: 2. A steel shaft rotating at 600 rpm is supported by two bearings as shown. E=30 Mşi, d=1.0" (inch),…

A: Assume the shaft is static initially and evaluate the reaction forces at bearing supports.Consider…

Q: 4. The shaft shown below, is made of ASTM-A-36 steel with Sy = 250 MPa and p = 7.86 g/cm³. The…

A: The weight density is The yield stress is The torque aplied is The length of shaft is

Q: The end gear (closest to the journal bearing at A) is subjected to the loading shown in the figure.…

A: Given: The yields strength of material = 80 MPa

Q: Two aluminum circular shafts (E=70GPA) are mounted according to the figure. The two shafts have the…

A: r1 = 6.9 mm r2 = 11.11 mm L1 = 1.52 m L2 = 1.29 m P = 2.1 kN

Q: The figure above shows a shaft subjected to a force P = 20 kN and a moment Mv = 600 Nm. Other data:…

A: The force applied is The moment torque is The dimension are

Q: as a diameter ofd₁= 57 mm and length ofL₁= 0.75 m; segment 2 has a diameterd₂= 44 mm and lengthL₂=…

A: Twisting Moment:- A couple of forces produce a moment in a material that is known as a twisting…

Q: A simple torsion-bar spring is shown. The shear stress in the steel [G= 11,500 ksi] shaft is not to…

A: The shear stress in steel is The modulus of rigidity is The vertical deflection at D is .The load…

Q: Calculate the normal stress and the shear Stress at Points C and D The shaft is hollow; inner and…

A: shear stress at points C and D for a hollow shaft subjected to axial force (N), bending moment (M),…

Q: Note: J3 = J2 46 mm G3 = G2 4.93×10 mm (1) 16 kN-m 50 GPa (2) 34 mm %3D (3) 2.10x106 mm 900 mm 35…

Q: A 3 m long steel angle shown in the figure has a section thickness of 12.7 mm and a cross sectional…

Concept explainers

Pressure Vessels

The term pressure vessel refers to a closed container that contains gas or liquid at a different pressure than environment pressure. The pressure vessels have a wide scale of applications in our day-to-day lives and other industrial places. Some common examples of pressure vessels are gas cylinders, autoclaves, compressor vessels, etc.

Question

Consider the compound shaft KC which is composed
of a 1200mm long solid rod fitted snuggly into an
equally long pipe. Refer to the figure for given
dimensions and material properties.
If end K is fixed to a rigid wall and a concentrated
torque is applied at end C, determine the following:
Pipe
E
115 GPa
G = 36.0 GPa
48.0 MPa
Ty
1200 mm
ø180mm Rod
E = 220 GPa
G
85.0 GPa
80.0 MPa
1. The required outer diameter for the pipe such
that the rod and the pipe yields simultaneously.
2. The corresponding maximum angle of twist of
the shaft when it yields.
3. The corresponding maximum torque T that can
be applied at end C of the shaft

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

= The L 37 in. long structural member shown below is fabricated with a solid copper core and a stainless steel cover that are bonded together to form a composite shaft. The copper core has diameter Dc = 1.4 in The stainless steel cover has inner diameter (Din)s = 1.4 in. and outer diameter (Dout) ss ss = с = 1.65 in. A torque of T = 104 ft lb is applied at its free end, which is shared between both the copper and stainless steel. Determine the angle of twist of the composite shaft and the maximum shear stresses in the copper core and the stainless steel cover. = -.39 (Tmax) ss = 869.295 (Tmax) c = = 1834.97 L Stainless steel Copper core ? × 0% psi × 0% psi ? × 0%
The shaft in Figure below consists of a 3-in. -diameter aluminum segment that is rigidly joined to a 2-in. -diameter steel segment. The ends of the shaft are attached to rigid supports, Calculate the maximum shear stress developed in each segment when the torque T= 10 kip.in is applied. Use G = 4×106 psi for aluminum and G = 12×106 psi for steel. Aluminum 3-in. diameter 6 ft T Steel 2-in. diameter 3 ft
5 - A thin-walled pressure vessel is subjected to internal pressure p 1 MPa. What is the maximum allowable torque T, applied along the longitudinal axis, if the maximum allowable tensile stress is 80 MPa? ↓t=3mm 240mm polar moment of inertia J=2r³t
A round shaft of diamater D = 65 mm with a groove cut into it where the diameter decreases to d = 50 mm. The radius of the fillet at the groove is r = %3D 2.5 mm. If the internal torsional moment at a critical cross-section in the groove is 400 N.m, calculate the maximum torsional shear stress at the groove. Round-up your answer to the nearest MPa. Max torsional shear stress MPa