Consider the circuit shown in figure, where Vee=700 mV, B = 100, and VA = 00. Calculate the VCE of Q1. Assume that the emitter current is equal to collector current. Circuit parameters / Rg = 140 k, Rc = 0,7 kQ, Rɛ = 0,3 k), Vcc = 12 V .Vcc RB Rc 는 RE

Consider the circuit shown in figure, where Vee=700 mV, B = 100, and VA = 00. Calculate the VCE of Q1. Assume that the emitter current is equal to collector current. Circuit parameters / Rg = 140 k, Rc = 0,7 kQ, Rɛ = 0,3 k), Vcc = 12 V .Vcc RB Rc 는 RE

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Re £ Value ZRB 꿀 Consider the transis BE=0.70 The Circuit has the Cirsuit Shown. Let B = 150 Cirbuit shown. and assume that shown .RB below PIRE Rc 47 ки base Current, IB Collector Current, I Mortage 74702 Is V 1201002 the Determine 3. Determine the Determine the Cmitter Vee Determine the value of RB that sets Vce = 0.3 V 2.3 between the Collector and
3. An electrical fan is used to cool electrical components when the temperature exceeds a certain limit. The fan is controlled by a microcontroller that sends a logical-1 (3.3V) to an interface circuit that in turn activates the motor. When the temperature falls below the upper limit, the microcontroller sends a logical-0 (0.0V) to the interface circuit and the motor turns off. You are to design a simple transistor switch controller circuit for this application and decide to use the design shown Fan motor draws V2 24W when running "GND -24V D2 IN40010P u2 "DO" as NPN Transistor Ib below. You have the following npn transistors available to you: 2N2222A, SS8050, and 2N3904. a. If the fan draws 24W when running, what is the collector current, Ic? b. What would the maximum Vce voltage be across the transistor when the it is in cut-off? c. Based on the design criteria and the manufacturer's specifications for the 3 transistors, which one would work for this application? Why? d. For the…
1. (a) An emitter follower as shown below should provide an input impedance of 2 k with a gain of 0.75. Determine the required bias current (collector current) and RE, assuming ß= 80 and V₁= ∞o. (b) How does the gain change if considering the internal resistance Rs (not shown in the figure) of the signal source of 500 ? Vcc=2.5 V J VinQ₁ WI RE Vout
Draw an I/V characteristic diagram to connect the common emitter, indicating on it the operating point Q and the load line with simplified explanation.
Given the circuit in the Figure, determine the emitter current and the collector-base voltage VCB. Assume the offset voltage is V₁ = 0.6V. 20 ΚΩ ww 20 V 39 ΚΩ 20 V
8.
For the circult shown in the given figure. Rc-2.4 k0, Rg-10 ko. Pmin-50, and Vcc=5 V. Determine the range of values of Vgg 50 Ic that the transistor is in saturation. Assume Vy-0.6 V and VCEsat -0.2 V. The range of values of VB8 Is VBB> 12 V Ra VAR со Va VCE OE RC Ncc
A base bias method is used in the following circuit. For Bpc - 300, the value of emitter current is: -Vc. +15 V Rc 1.8 k2 RB 560 k2 7.82 mA O 6.84 mA O 7.27 mA
electronics
In an emitter-biased transistor circuit, we have collector source voltage V CC = 15 V, collector resistance RC = 3.5 kOhm, emitter voltage V_E = 4.3 V and emitter current LE = 2.1 mA. If the current gain is 150, what is the difference in emitter-collector voltage V_CE when we calculate it including the gain factor vs when it is calculated by assuming collector current LC = LE? Select one: O a. 3.35 V O b. 3.40 V OC 0.05 V O dov
The operating point of the npn transistor is defined by a couple of values: Icand Ver- Select one: OTrue O False In the following figure. Q, and Q: are identicaland operate in active mode. if la =9 Icz then V,V2 IC
For the given circuit, Vcc = 19 volts, Rg = 900 KN, Rc = 8 KN, RE = 3 KN and B = 100. Assume Transistor is Silicon, VBE=0.7 volts. Vcc RC RB RE a. Compute for the base current Q-point, IBa (in Amperes) [ b. Compute for the collector current Q-point, Ica (in Amperes). c. Compute for the collector-to-emitter voltage, VCEQ (in Volts) d. Draw the Load Line, with details.'