Consider the automobile hydraulic system shown in the figure below. 0.60 cm F. 0.040 F2 0.20 m Master cylinder F= 100 N Slave A force of 100N is applied to the brake pedal, which acts on the cylinder-called the master-through a lever. A force of 500 N is exerted on the master cylinder. Pressure created in the master cylinder is transmitted to four so-called sla cylinders. The master cylinder has a diameter of 0.60 cm, and each slave cylinder has a diameter of 2.50 cm. How much pressure is transmitted in the hydraulic system? Express your answer in pascals and in atmospheres. pressure in Pa Pa pressure in atm atm

Consider the automobile hydraulic system shown in the figure below. 0.60 cm F. 0.040 F2 0.20 m Master cylinder F= 100 N Slave A force of 100N is applied to the brake pedal, which acts on the cylinder-called the master-through a lever. A force of 500 N is exerted on the master cylinder. Pressure created in the master cylinder is transmitted to four so-called sla cylinders. The master cylinder has a diameter of 0.60 cm, and each slave cylinder has a diameter of 2.50 cm. How much pressure is transmitted in the hydraulic system? Express your answer in pascals and in atmospheres. pressure in Pa Pa pressure in atm atm

Name: Consider the automobile hydraulic system shown in the figure below.0.
Uploaded: 2024-03-20T06:51:10.000Z
Channel: Bartleby
Description: Consider the automobile hydraulic system shown in the figure below.0.60 cmF. 0.0400.20 mMastercylinderF= 100 NSlaveA force of 100N is applied to the brake pedal, which acts on the cylinder-called the master-through a lever. A force of 500 N is exert

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Related questions

Q: A hydraulic lift is used to jack a 960-kg car 41 cm off the floor. The diameter of the output piston…

A: Given data: The input force , F1=360 N The mass of the car m=960 kg The diameter of output piston…

Q: A sump pump (used to drain water from the basement of houses built below the water table) is…

A: The rate of drain of water by the pump is Q=0.55 L/s=0.55 L/s×1 m31000 L=0.55×10-3 m3/s. The output…

Q: A round pipe of varying diameter carries petroleum from a wellhead to a refinery. At the wellhead,…

Q: Water flows at 0.9 m/s from a hot water heater, through a 410 kPa pressure regulator. The pressure…

Q: A waste management company handles large dumpsters of construction debris. The sorting process…

A: Pressure on input piston, P = 3.60×106 Pa Radius, r = 0.120 m Consider the distance from rotational…

Q: Liquid of density 945 kg/m is flowing through a pipe as shown in the diagram below. At point A, the…

A: Answer B) -1.36 X 10^6 Pa

Q: 26. A block of density 2700 kg m-3 is attached to a spring with spring constant k. The block is…

Q: Assume your home uses the water pipe system below where a pump produces a pressure of P1 =…

Q: You build a pressure gauge as shown in the figure below. The spring has spring constant of 1000 N/m…

Q: in the picture. Question A: If the hot water is pumped into a 5.0 cm diameter pipe at 0.60 m/s how…

Q: The pressure at the bottom of aquarium A is greater than that at the bottom of aquariur B. Why might…

A: Formula of pressure at the bottom of aquarium: P=Po+ρgh=Po+mVgh Where, P = Pressure at the bottom.…

Q: The spring of the pressure gauge shown in the figure below has a force constant of 1 000 N/m, and…

A: The force needed to move the piston is,Substitute the values,

Q: A waste management company handles large dumpsters of construction debris. The sorting process…

A: absolute pressure into the input piston,p=3×106 Paradius of output plunger,r=0.245 m

Q: There is a force exerted on piston A which has a diameter of 0.050 cm. This produces an output force…

A: Given data: Diameter of piston B (dB) = 0.15 cm Diameter of piston A (dA) = 0.05 cm Force on the…

Q: Two identical cylindrical vessels with their bases at the same level each contain a liquid of…

A: Density of liquid, ρ = 1.18 g/cm3=> ρ ==> ρ = kg/mArea of base, A = 2.91 cm=> A = m2Height…

Q: The drawing shows an intravenous feeding. With the distance shown, nutrient solution (p = 1050 kg/m)…

A: The pressure due to the fluid is given by P = h d g where, h is the height of the fluid, d is the…

Q: A swimming pool is 6 m deep, which can be drained by a valve located at the bottom. The valve is…

A: a) Pressure at valve P=P0+ρgh P=1.013*105+1000*9.8*6=1.60*105Pa

Q: A large man sits on a four-legged chair with his feet off the floor. The combined mass of the man…

Q: The pipe goes up to the second floor of the building, 2.0 m higher, and the pressure remains…

Q: *96. D A log splitter uses a pump with hydraulic oil to push a piston, which is attached to a…

A: The pressure is given by, P=FA Here, F is the force and A is the area of cross-section. Rearranging…

Q: The spring of the pressure gauge shown in the figure below has a force constant of 1 500 N/m, and…

Q: Water is pumped at a speed of 0.5 m/ s through pipe 1 with a diameter of 4 cm on the ground floor…

A: Given : Velocity of pipe 1 = 0.5 m/s Diameter of pipe 1 = 4 cm Height of…

Q: A force of 295 N is applied to a hydraulic jack piston that is 0.026m in diameter. The second piston…

A: Given data: Force applied to first piston (F1) = 295 N Diameter of first piston (d1) = 0.026 m…

Q: The drawing shows an intravenous feeding. With the distance shown, nutrient solution (p = 1020…

A: We are given that solution can just barely enters the blood in the vain. That means at both ends the…

Q: 9. A fountain shoots water 8 m straight up. a. What is the pressure at the point where the water…

A: Given : Height of the fountain, h = 8m Determine : a) the pressure at the point where…

Q: The spring of the pressure gauge shown in the figure below has a force constant of 1 300 N/m, and…

A: Spring force = pressure force please find the image below

Q: The figure shows 4 containers containing a liquid X. If in all the containers the level of the…

Q: The figure below shows 5 containers of water. A and B have the same height, as do C and E. A and E…

A: The pressure is given by, P=ρgh P∝h Given, The height of the A and B containers is the same. The…

Q: A 70.0 kg person balances a 1200 kg elephant which is standing on a 1200 kg circular lift of…

A: Consider the mass of the student is Ms=64 kg Mass of elephant is Me=1200 kg The diameter of the…

Concept explainers

Fluid Pressure

The term fluid pressure is coined as, the measurement of the force per unit area of a given surface of a closed container. It is a branch of physics that helps to study the properties of fluid under various conditions of force.

Gauge Pressure

Pressure is the physical force acting per unit area on a body; the applied force is perpendicular to the surface of the object per unit area. The air around us at sea level exerts a pressure (atmospheric pressure) of about 14.7 psi but this doesn’t seem to bother anyone as the bodily fluids are constantly pushing outwards with the same force but if one swims down into the ocean a few feet below the surface one can notice the difference, there is increased pressure on the eardrum, this is due to an increase in hydrostatic pressure.

Topic Video

Question

Consider the automobile hydraulic system shown in the figure below.
0.60 cm
F. 0.040
0.20 m
Master
cylinder
F= 100 N
Slave
A force of 100N is applied to the brake pedal, which acts on the cylinder-called the master-through a lever. A force of 500 N is exerted on the master cylinder. Pressure created in the master cylinder is transmitted to four so-called slave
cylinders. The master cylinder has a diameter of 0.60 cm, and each slave cylinder has a diameter of 2.50 cm. How much pressure is transmitted in the hydraulic system? Express your answer in pascals and in atmospheres.
pressure in Pa
Pa
pressure in atm
atm

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, physics and related others by exploring similar questions and additional content below.

Similar questions

A log splitter uses a pump with hydraulic oil to push a piston, attached to which is a chisel. The pump can generate a pressure of 2.4x107 Pa in the hydraulic oil, and the piston has a radius of 0.035 m. In a stroke lasting 15 s, the piston moves 0.69 m. What is the power needed to operate the log splitter's pump? Number i Units
A waste management company handles large dumpsters of construction debris. The sorting process starts by downloading the dumpster from the transport truck and then dumping its contents into a large hopper as shown below. The waste management plant uses a hydraulic cylinder arrangement to tilt the dumpster to the point that the force of gravity will empty the contents. The plant operator activates an electric pump that pumps hydraulic oil into the input piston at an absolute pressure of 2.50 x 106 Pa and drives the output plunger, which has a radius of 0.230 m. If the design of the dumping arrangement is such that the output plunger remains perpendicular to the floor of the dumpster, determine the torque the plunger creates about an axis at the end of the dumpster. Enter a number. Frect pressure to use for the pressure in the oil at the site of the input piston? According to Pascal's Law, how is the pressure in the oil at the site of the output plunger related to the pressure in the oil…
The spring of the pressure gauge shown in the figure below has a force constant of 1 350 N/m, and the piston has a diameter of 1.40 cm. As the gauge is lowered into water in a lake, what change in depth causes the piston to move in by 0.700 cm? 4.635 X Your response differs from the correct answer by more than 10%. Double check your calculations. m Vacuum
A tank in the shape of an inverted cone has a height of 20 meters and a base radius of 11 meters and is filled with liquid to a depth of 16 meters. Determine the amount of work needed to pump all of the liquid to a point 1m from to the top of the tank. Assume that the density of the liquid is 793 kg/m 3
The figure below shows 5 containers of water. A and B have the same height, as do C and E. A and E have the same area on the bottom, as do B and C. D has the largest area and the lowest height. Rank the pressure at the bottom of each container, from least to most (least occurs first, most occurs last). AVİLI O D, A=B, C=E O C=B, A=E, D OD, С, В, А, Е ОС, В, А, Е, D O D, A-B, C, Е
A tank holds a large amount of water. A pipe is connected to the tank at the upper end and is open to the air at the lower end (see figure).The upper end of the pipe has a diameter of 17.0 cm. The lower end of the pipe has a diameter of 8.60 cm. The speed of the water at the upper end is 2.00 m/s.What is the flow rate of the water in the pipe?
Two identical containers are open at the top and are connected at the bottom via a tube of negligible volume and a valve that is closed. Both containers are filled initially to the same height of 1.00 m, one with water, the other with mercury, as the drawing indicates. The valve is then opened. Water and mercury are immiscible. Determine the fluid level in the left container when equilibrium is reestablished. Number Units Water Valve Mercury 100 m 4
While taking a shower, you notice that the shower head is made up of 36 small round openings, each with a radius of 2.00 mm. You also determine that it takes 2.00 s for the shower to completely fi a 1.00-liter container you hold in the water stream. The water for the shower is pumped by a pump that is 5.60 m below the level of the shower head. The pump maintains an absolute pressure of 1.50 atm. Use g = 10 m/s?, and assume that 1 atmosphere is 1.0 x 105 Pa. (a) At what speed does the water emerge from the shower head? 1.105 m/s (b) What is the speed of the water in the pipe connected to the pump? m/s (c) What is the cross-sectional area of the pipe connected to the pump? m2