Consider he T-beam cross-section shown in Figure 4. Using the coordinate system provided find: a) the position of the centroid of the composite area (î, g); b) the moment of inertia of the composite area about a centroidal axis parallel to x. h b b/2 h b Figure 4: T shape cross-section.

Q: Determine the equation of the influence line for the reaction at A in the continuous beam shown in…

A: By Muller Breslau method, As we have to find the reaction at end A, hence Support at A will be…

Q: Jse commands (rectangle, mirror) and List he commands to draw the following drawing start from a…

A:

Q: y 130 mm 30 mm 30 mm -40 mm 40 mm-

A:

Q: What is this called?

A: Chisel

Q: How can I find GH, EG and FH

A:

Q: Find the shortest distance from point B to line AC

A:

Q: Can you help me figure out the different symbols and how many of them are there and put them in…

A: Single Pole Switch Duplex Outlet Quadruplex Outlet Electrical Outlet Fan Outlet Wall Mounted…

Q: answer in 4 decimal places

A:

Q: determine the distances x and y for equilibrium if f1=800 N and f2=1000N. (Hand written and clean…

A: Given data - F1 = 800 NF2 = 1000 N Find out - Distance x and y ?

Q: Find the centroid of the following cross-sections and planes.

A: Centrodal distanceX = 5.333 inY = 5.667 inExplanation:Step 1:Step 2:

Q: -160 40 160 Dimensions 40 in mm 40 -160- –160-

A:

Q: FIHD THe CENTROID (x $ Y) of THe GazOMETRY

A: Centroid is the point where the mass of whole body acts. If there is a figure which consists of…

Q: A clockwise couple M = 4.5 N m is resisted by the shaft of the electric motor. (Figure 1) Part A…

A: Given: The moment M is 4.5 N.m. Consider the figure,

Q: y 500 50 80 -140- - 140- 80 60 400 500 50 500

A: Given- plate area is given  To find- centroid of given plate area

Q: usescale (1/1) draw the front Section view in mides pan and the side Sectional Vien middles pan for…

A: Front Sectional View: The front sectional view is the view of the object done by taking a section…

Q: XXXX W₂ W₁ Which of the following most nearly gives the external degree of indeterminacy? 2 4 O 1

A:

Q: 3. Name any two-pattern material.

A: Introduction- There are several types of material found in nature. Some materials form certain…

Q: 31⁄5 / 4⁄7

A: 31/5=6.2 4/7=0.571

Q: show the (c)

A:

Q: What is Ergun equation?

A: Answer Introduction Ergun equation is the extension form of Darcy's Law. The Ergun equation is used…

Q: The representation of the hinge lines of the glass box in a drawing are known as lines. ....** .....…

A: The glass box concept is used in orthographic projection. When the glass box is visualized, then…

Q: 4) A precast T beam with the dimensions shown below is to be a used as a bridge over a small…

A: As per Bartleby's guidelines we are supposed to answer only first three questions. Kindly repost…

Q: Determine the y-coordinate of the centroid of the shaded area in terms of h.

A: GIVEN: Triangle having base 2h and height h from which semicircle is cut out of radius h/2   To find…

Q: 3. Is Iust be par PROBLEM 1: The frame shown is supported with hinges at A and C and a pin at B.…

A: Both the hinges will have the two supports, they are :- RAx and RAy at A and RCx and RCy at C. Then…

Q: where did 3sqrt of 2 came from?

A: Given, A structure with carrying varying load   To find : Where 32 came from.

Q: Describe how the design of a bridge begins in the mind.

A: Bridges are constructed when there are obstacles in the transportation system such as rivers,…

Q: The 4th root of 81

A: Answer : 3

Q: i dont understand step one, this is very vague

A: Given data in question  Load 2 kN Dimensions 10 m and 2.5 m To find out  Step 1 understanding

Types of Composite

Composite materials are formed by merging two components that have different chemical and physical properties. The merged output is termed as a composite, whose properties are completely different from the individual components. Composite materials also have better strength than the individual components.Composite materials usually have two main parts, reinforcement material, and matrix material. The matrix material acts as a binder and surrounds the fiber of another material that bears a much higher strength. This material is known as the reinforcement material. The matrix materials are usually high-strength additives resins, while the fibers of the reinforced material can be random, oriented, and in a mat format.Composite materials are also known as fiber-reinforced composite polymers because they are composed of the polymer matrix which is reinforced to laboratory-created fibers or naturally occurring fibers, such as glass fibers, carbon fibers, or aramid fibers. Under the application of external loads, the matrix material absorbs and transfers the loads to the fibers, these fibers in return provide good compressive strength, tensile strength, and stiffness to the fiber-reinforced composite materials.Depending upon the matrix and the reinforcement material, different properties can be induced to the fiber-reinforced composite materials, including good corrosion resistance properties. The most common matrix material is the resin while the glass fibers act as the reinforcement material. Strong fibers provide strength and stiffness to the composite materials while, a soft and flexible resin provides shape to the composite materials.