Consider FM radio, which consists of 200 channels, each 150 kHz wide, and with 50 kHz guard bands between them. a) Calculate the channel spacing. b) Make an approximately scale drawing showing five of these channels and their guard bands. Make the leftmost channel be centered at 96.5 MHz. An extra diagram is provided if needed.

Q: What is a receptacle?  What is meant by “service drop”? What are sets of service-entrance…

A: As per the guidelines given, we can only provide the solution of one question in multiple type of…

Q: Often, the network is referred as an infinite bus when a change in input mechanical power or in…

A: In power systems many generator buses are connected together to form infinite bus.

Q: Generation engineers are more inclined to an operation in a closed system as compared to an open…

A: Nowadays Electricity is a major part of any country's growth. The demand for power supply is…

Q: True or False: It's safe to place someone in the recovery position who is not responding to you but…

A: The 1st statement is absolutely true since

Q: The concept of the state of a dynamic system refer to a .maximum set of variables The root locus is…

A:

Q: AMoving to another question will save this response. uestion 8 Which of the following is the phase…

A: In this question we need to choose a correct option.

Q: Why make two wire, three wire or four wire connection in RTD connection

A: Why make two wire, three wire or four wire connection in RTD connection?

Q: 5. What was the effect on the motor power factor as the load increased? 6. What was the effect on…

A:

Q: i) Design appropriate CT ratios for CTA, CTB, and CTC. (ii) Estimate time of Operation for all three…

A: Dear student you asked to solve the question with multiple sub part.we have limited time for solve…

Q: please could give a simplified drawn schematic/diagram to show a how  microcontroller is connected…

A: The above question is based on the interfacing of a microcontroller to a relay circuit.

Q: Fill in the blank: In splicing the fiber alignment can be tuned using a visual fault locator.

A: In... Splicing the fibre alignment can be tuned using a visual fault locator.

Q: 5. Siemens and A-Bhave different contact descriptors for the same functions. In the following, the…

A:

Q: write an objects for three-phase system with load on transformer (open and short circuit )

A:

Q: 2. Isolated power systems installed in healthcare facilities are required to A. have an…

A: Power system:- It is a connection of electrical components. Power plant, transformer, transmission…

Q: 1) Describe the operational features of digital power relay and circuit breaker designed to protect…

A: I am solving parts (1) & (2) only as Figure 1 is not mentioned in part (3). Please provide a…

Q: a) Determine the sampling rate for an analog telephone signal transmitted across a single channel of…

A: As here multiple questions are available I am solving first two parts, a & b a)

Q: Define percentage line and load regulation

A: Line regulation-Line regulation refers to a power supply's capacity to maintain a constant output…

Q: Fill in the blank: In splicing the fiber alignment can be tuned using a visual fault locator.

A: In fusion splicing, the fibre alignment can be tuned using a visual fault locator.

Q: Please answer in typing format and don't be AI solution either i will dislike

A: When you're measuring power in a three-phase system, the phase sequence matters because it affects…

Q: Explain the operation of thermochemical energy storage system.

A: Thermal energy from the sun can be stored as chemical energy in a process called solar…

Q: Underground cables are least affected by lightning. Select one: O True False

A: Underground cables are least affected by lightning .

Q: An REJ525 relay with a 5 A rated current is connected through a CT with a ratio of 129 to a primary…

A: Given data: CT ratio=129Ip=8751A

Q: With the aim of a schematic, explain the principle of high impedance busbar protection.

A: High impedance bus bar protection requires High impedance CT with high knee point voltage and the…

Q: What do you mean by cutoff voltage for JFET?

A: The JFET is the abbreviation for junction field effect transistor. There are two types of JFET…

Q: Block diagram of Arduino car speed Detector ana explains operating

A: consider the given question;

Q: What happens when you use cables longer than the prescribed length in a network?.

A:

Q: Draw the circuit diagram of Two quadrant chopper which is having average load current might be…

A: Chopper: Chopper is a device which transfers the dc power from one circuit to another circuit. Two…

Q: Can coaxial cable terminate with RG-6 coaxial cable

A: Coaxial cable can be used to transmit a variety of signals, including cable television, internet and…

Q: 3 ● Row 1 2 4 5 6 7 8 9 10 11 12 13 14 15 Refer to the National Electrical Code® or the working…

A: Here it is asked to solve question (2), so we are solving that question only. “Since you have posted…

Q: Explain LVDT with neat sketch.

A: The construction of LVDT is shown in figure. LVDT translates the linear motion into electrical…

Q: Explain about PI Control of the Integrating Pumped Tank Process

A: According to question we have to explain about PI control of the integrating pumped tank process.

Q: COMMON TRIGGERING COMPONENTS, USED FOR START UP, CONDUCT ANOTHER SEMI CONDUCTOR COMPONENTS

A: Types of semiconductors devices / switches  Uncontrolled semiconductors ( Diode) Semicontrolled…

Q: Deviations in quality of service include power irregularities. Which irregularity occurs when…

A: This problem is from power system.  The solution is given below.

Q: . What's the primary instrument for locating a break in a cable during emergency maintenance? A. OSA…

A: In this question we need to choose a correct option

Q: 4) Reduce the block diagram of the system using Mason's Rule. Rist Dy Xx(x) -26 -24

A:

Q: Explain the following for underdamped response of second order system. 1. Overshoot 2. Decay Ratio…

A: Consider the below block diagram; Here the transfer function of the block diagram is; TF=CsRs…

Q: what is the receptacle load (after demand factors) for an office building with 250 receptacle…

A: Receptacle loads are described as equipment loads that are generally served by electrical…

Q: Analyse several voltage and current situations in different loading scenarios in a simplified radial…

A: 1. Understanding the ProblemYou are analyzing a simple radial medium-voltage (MV) power system with…

Wheatstone Bridge Method

A Wheatstone bridge is a circuit used to measure unknown resistance by measuring the ratios of the two branches of the circuit such that each branch has two resistance and out of four resistance one is unknown. The two branches are joined in between with the help of galvanometer which is used to determine the direction of the current. The main advantage of this circuit is that it can provide the most accurate measurement (different from a simple voltage separator).