Consider an industrial network application where there is one control unit (PLC) connected using half duplex connection with 20 other sensor and actuator devices having a bandwidth of at least 100Kbps located at the distance of around 2000 feet apart. Choose a most suitable fieldbus protocol and serial communication protocol along with wiring, cable, topology and any other requirement details to connect all these devices efficiently.

Q: 15.a. You're planning an installation of fiber optic cables in several locations in a building.…

A: planning an installation of fiber optic cables in several locations in a building outside diameter…

Q: Explain the concept of modulation in wireless communication and its significance in transmitting…

A: Modulation in wireless communication is a technique used to transmit data over radio waves. It…

Q: What information can be obtained by reading the abstract of  "Enhance AM radio signal broadcasting"

A: AM broadcasting is radio broadcasting using amplitude modulation (AM) transmission . It was the…

Q: Draw a block diagram of a typical digital communications system (both transmit and receive paths)…

A: Given  We need to draw the block diagram of digital communications system and explain source encoder…

Q: -In 8086 microprocessor, carry flag may be set by the instruction LEA. O CWD. SUB. NOT. -A name or…

A: The solution can be achieved as follows.

Q: Analyze the latch circuit shown below by obtaining timing diagram for the circuit; include…

A: Given data Given flip-flop SR-circuit.

Q: 12. More spares should be purchased for equipment with a small A. receiver sensitivity threshold. b.…

A: The Mean time between failures indicates or predicts the duration between successive failure of a…

Q: q4-  In spread spectrum communications, a pseudo-noise (PN) sequence converts _______ signal to…

A: spread spectrum communications : Spread Spectrum refers to a system originally developed for…

Q: What are the steps required in order to solder the RFID for the arduino? and what are the benefits…

A:

Q: The System y(n)= 5 x(n) + 10 ans. Static   Dynamic

A: We are authorized to answer one question at a time, since you have not mentioned which question you…

Q: Discuss the various modulation techniques used in wireless communication systems and their…

A: To discuss:Discuss the various modulation techniques used in wireless communication systems and…

Q: Why we use FT-IR instrumentation?  Please shortly answer at your own words.

A: The explanation is as follows.

Q: (a) Perform binary addition of the following numbers: 110111101.10011+ 100010101.11110 (b) Represent…

A:

Q: In an FDMA-based multiple access system, each user is assigned an 80 kHz channel for full-duplex…

A:

Q: How does "rotational latency" affect the performance of traditional HDDs?

A:

Q: The superheterodyne receiver (SuperHet) is an architecture that enables the same receiver to pick-up…

A: According to the question, for the SuperHet receiver (i) Draw and explain the block diagram of the…

Q: Explain the application of DSP in communication. *The question from a communication engineering.

A: DSP is known as digital signal processing.  It is used to improve the  accuracy and  reliability of…

Q: Design a mode 7 to 3 backcounter circuit.

A: Design a Mode 7 to 3 back counter circuit (Using T Flip-flops), which counts from state 7 to state…

Q: Describe the operation of a Superheterodyne receiver? For which modulation schemes can it be used?…

A:

Q: Why GNSS and dual-frequency receivers are mostly preferred?

A: GNSS stands for Global Navigation Satellite System is a navigation system used for identifying…

Q: How is adaptive modulation implemented in Mobile Candy 33919 pue SOMEON

A: Adaptive modulation in mobile networks and wireless communications is implemented through techniques…

Q: Find the communication speed if given: Value in register SCIO.BRR = xEFh and value in register…

A:

Q: 11. Pulse code modulation is preferred to PAM because of ______________. 12. Most FDM telemetry…

A: Pulse code modulation is preferred to PAM because of ______________.12. Most FDM telemetry systems…

Q: 6.40 The V.32 modem standard with nonredundant coding uses a rectangular 16-QAM con- stellation. The…

A: Rectangular 16-QAM constellationfc=1800HzSymbol rate=2400 baudsAverage…

Q: Explain the importance of power delivery systems, such as voltage regulation modules (VRMs), on a…

A: In the intricate ecosystem of a computer motherboard, Voltage Regulation Modules (VRMs) may not…

Q: List the reasons why the modulation is desired in a wireless communication system considering the…

A: Modulation is a technique that is used in carrier wave to transmit some information at low…

Q: c) The superheterodyne receiver (SuperHet) is an architecture that enables the same receiver to…

A: Introduction - Superheterodyne receiver - A superheterodyne receiver, also known as a superhet, is a…

Q: In spread spectrum communications, a pseudo-noise (PN) sequence converts _______ signal to ______…

A: Need to identify the function of Pseudo - noise(PN) sequence based on the given option.

Q: elect an embedded system and discuss parts of Security Target (ST) and Target of Evaluation (TOE).…

A: Attack path identification as well as exploitation analysis and tests are mapped to relevant…

Q: 1) Assume that a circular cell has 57 channels and a cell radius of 10 km. The transmit power of the…

A: No of channels=57 Radius=10km Power=32Watt Grade of service=5% Path loss=4 H= 2 minutes λ=2…

Q: Why is low-frequency operation the most reliable for TRIACs?

A: TRIAC is a type of thyristor . TRIAC is capable to conduct in both direction.

Q: A network operator has asked you to design a point-to-point optical link for short reach (2 km)…

A: GIVEN data:

Q: (a) Sketch the satellite communication system between the transmitter and the describe the type of…

A: A satellite communication is define as the communication which has an involvement of satellite…

Q: 4. Discuss general structure of the LTE frame with the aid of clear graphics.

A:

Q: Which of the following statements are appropriate for the SPI bus (select all that apply): SCLK is…

A: SPI is known as Serial Peripheral interface. It is used for communication in embedded system.

Q: Illustrate the working of differential pressure transmitter with neat diagram.

A: differential pressure transmitter: An electrically insulating fill fluid (often a liquid silicone…

Q: In the FCC Emission Designation the first symbol indicates? a. the type of information to be…

A:

Q: Discuss the need for interfacing circuitry to make the signals produced by sensors compatible with…

A: According to the question, we need to discuss the need for interfacing circuitry to make the signals…

Q: 51, If two Huawei S5700 switches are connected through 10GE optical modules, the connecting ports…

A: An optical module is a photoelectric converter that transforms electrical signals into optical…

Q: 4. Explain the benefit of using IF stage in super heterodyne receivers.

A: The IF stage's full form is intermediate-frequency amplifiers and the benefits of using this stage…