Consider a worker-machine system that consists of external manual work elements (E), machine work elements (M) and internalments (1). Normal times of E, M and I are 2.9, 1.7 and 2.3 minutes, respectively. Assume PFD allowance factor as 15 % and aowance factor as 10 %.=) The standard time for the cycle isminutes.) Number of work units produced daily (in 8-hour shift) at standard performance is-) The worker efficiency given that the worker produces 100 units is96.a talented engineer and may increase the productivity of the worker-machine system. He internalized some of external workartially, which sums up to a total of 0.4 minutes. Under this new setting, E decreases by 0.4 minutes and l increases by 0.2 minutes.) Under this new setting, the standard time for the cycle isminutes.) Number of work units produced daily (in 8-hour shift) at standard performance under this new setting is) Cost of applying Fahrettin's improvement requires about a 1100 work units production. Therefore, the application cost willdays.раy

Hello. Since your question has multiple sub-parts, we will solve first three sub-parts for you. If…

Consider a worker-machine system that consists of external manual work elements (E), machine work elements (M) and internal ments (I). Normal times of E, M and I are 2.9, 1.7 and 2.3 minutes, respectively. Assume PFD allowance factor as 15 % and a owance factor as 10 %. ) The standard time for the cycle is minutes. :) Number of work units produced daily (in 8-hour shift) at standard performance is ) The worker efficiency given that the worker produces 100 units is 96.

Consider a worker-machine system that consists of external manual work elements (E), machine work elements (M) and internal ments (I). Normal times of E, M and I are 2.9, 1.7 and 2.3 minutes, respectively. Assume PFD allowance factor as 15 % and a owance factor as 10 %. ) The standard time for the cycle is minutes. :) Number of work units produced daily (in 8-hour shift) at standard performance is ) The worker efficiency given that the worker produces 100 units is 96.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

None
A boiler provides 216 GJ of heat per hour to a steam engine providing work in the amount of 32.4 GJ/hr. a) Calculate the efficiency of this engine. b) How much heat is transferred to the cooling waters?
QI/Drive the work in polytrophic process when( n=1) ,(n=1.3)
moment of inertia Iz 465.8 in", determine: 5 in. Problem 3: The internal shear force V at a certain section of a steel beam is 110 kips. If the beam bas a cross section shown in the figure has a I in. a) the shear stress at point H. the maximum horizontal shear stress in the flanged shape. H. y'=6.7 in 1 in. 12 in. 110 kips Kpi 8 in. 1 in.
2. The capacity and use factors of a central station are 44.9% and 56.8%, respectively. The station was not used for 301.69 hrs during a certain period. The period covered is
B9
I need the answer as soon as possible
Calculate the net work per cycle, in kJ; B) the power developed by a motor, in kW and C) the thermal efficiency if the cycle is executed 1500 times in one minute. To answer the above, consider that the displacement volume of a Diesel internal combustion engine is 3 liters. The cutoff ratio is 2, and the conditions at the start of compression are set to 100 kPa, 22°C, and 3.17 liters.
B) An engine with an indicated thermal efficiency of 50% and mechanical efficiency of 45% consumes 15kg/h of a fuel at a fixed speed. The brake mean effective pressure is 6.5 bar and the mean piston speed is 13m/s. Assuming it is a four cylinder four- stroke square engine, determine the crank radius and the speed in rpm. Take the heating value of the fuel =42MJ/kg and combustion efficiency 100%.
In a perpetual motion machine, how much energy is waste energy?
12- Post Tests and Homework's: Q1. Following data is given for a rope pulley transmitting 24 kW: Diameter of pulley = 400 mm; Speed = 110 r.p.m; Angle of groove 45°; Angle of lap = 160°; Coefficient of friction 0.28; Number of ropes = 10; Mass in kg / m length of ropes 53 C2. The working tension is limited to 122 C2; where C girth (i.e. circumference) of rope in metres. Find the initial tension and diameter of each rope. [Ans. 675.55 N; 31.57 mm] - = ELVEN = iversity
LA Shn motor drives a solid 3/8" diameter steel shaft at 3,600 RPM, see Fig, below. Calculate the following G-10N O Msi.) a) Maximum shear stress in shaft b) Angle of twist (end A vs. end B) c) Maximum shear strain in shaft material d) Maximum normal stress in shaft material e) Maximum normal strain in shaft material Motor 3/8 Bearing 40