An air conditioned space is need to be maintained at DBT =24 c, RH= 50% . The sensible heat loss of the space is 66 kW and its latent is 16.5 kW. The space required 28.3 m/min fresh air .The outside design condition is DBT=7c, RH= 80% . a ) plot the air conditioning process on the chart. b) find the mass flow rate of the supplied air given that T, 49 c, c) the heating coil load d) the humidifier heating load ,e) the amount of steam required by the humidifier.

An air conditioned space is need to be maintained at DBT =24 c, RH= 50% . The sensible heat loss of the space is 66 kW and its latent is 16.5 kW. The space required 28.3 m/min fresh air .The outside design condition is DBT=7c, RH= 80% . a ) plot the air conditioning process on the chart. b) find the mass flow rate of the supplied air given that T, 49 c, c) the heating coil load d) the humidifier heating load ,e) the amount of steam required by the humidifier.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Find the heat lost or gained (a) between the evaporator coils and compressor, (b) between the compressor and condenser, and (c) to condenser water.
I need the answer as soon as possible
state T(C) P(bar) V(cm^3/g) H(KJ/Kg) S(KJ/kgK) 1(initial) 2(after throttle) 3(after cooling) 4(after compressor) fill out the number in the table
2. In an air conditioning system, if the recirculated air is three times the outside air and the mass of supply air is zokg/s, what is the mass of the outside air? Ans. 5kg/s
Note: Use the relevant chart for each problem.in addition to having the solution on a piece of paper Q1/ A refrigeration system operates according to reversed Carnot cycle, low temperature is -20 °C, high temperature is 43 °C, and the work done is 10 kW. Determined, the coefficient of performance as refrigerator and heat pump, absorbed heat and rejected heat.
A conference hall is to be i at 24 C dry bulb and 60 %RH. The estimated cooling loads are 75 tons and 25 tons sensible loads and latent loads, respectively. If cooled air from Air Handling Unit (AHU) is supplied to the hall at 15 C, determine the following below & plot the process on the Psychrometric chart. a) room sensible heat factor (RSHF) b) Bypass Factor (BPF) of the cooling coil c) the cubic per minute (CFM) needed to maintain the hall at its comfortable state at 24 C dry bulb and 60 %RH?
Q.4:A) A single-stage reciprocating compressor takes Ikg/min at 1bar, 288K and delivers it at 5bar calculate the indicated power required and isothermal efficiency, assuming that the law of compression and expansion is PV = C and that the clearance is negligible. B) A certain natural gas has the following volumetric analysis: 60% CH4, 13% H2, 18% CO, 6% CO, and 3% O2. This gas is burned completely with the stoichiometric amount of dry air. Determine the theoretical the air-fuel ratio and the mole fraction of each products.
Need help.
Liquid ammonia at a temperature of 26 OC is available at the expansion valve . The temperature of the vaporizing ammonia in the evaporator is 2 OC. a) Find the percentage of liquid vaporized while flowing through the expansion valve .b) The internal energy entering the evaporator. c) the cop of the heat pump .
Use 4 decimal places
Yes in their book its in the appendix 1. But you can find the table for R134A anywhere in google. Requirements: REQUEST TO YOU SOLVE ALL PARTS HANDWRITING THANKS FULL WARRANTY SOLUTIONS NEED . NO NEED GENERALIZED ANSWER OK
b) The compressor delivers gas at a constant pressure of p3 = 10bar to a tank via a valve with flow coefficient, C, = 5. The tank has a volume of 1.5m³. The air in the tank is initially at atmospheric pressure, and has the same temperature as the air exiting the compressor. Using the following valve flow rate equations, calculate the time required for the pressure in the tank to increase to 4 bar (abs). q = CyP3N (1– Ap 24p P3G,T3 3p3 If Ptank > P3/2. 1 If Ptank < P3/2. q = 0.471 C,p3N G,T Where N = 6950 when volumetric flow rate, q, has units = litres/min at standard conditions, temperature has units K, and pressure has units = bar (abs). Note that the specific gravity, Gg = (density of actual gas at standard conditions) / (density of air at standard conditions). c) The maximum volume of the compressor cylinder (i.e. V,) is 0.01m³. Calculate the rotational speed of the compressor required to deliver a mass flow rate of 0.2kg/s, and calculate the shaft power required to drive the…