Consider a wood beam (see figure) carrying a uniform load of 21.5 kN/m (which includes the weight of the beam). The length is 2.25 m and the cross section is rectangular with width 150 mm and height 300 mm. 21.5 kN/m 300 mm 150 mm 2.25 m (a) 21.5 kN/m 2.25 m (b) (a) If the beam is simply supported as in figure part (a), calculate the maximum shear stress max and the maximum bending stress max (Enter the magnitudes in MPa.) = max MPa MPa max = (b) If the beam has a sliding support at right as in the figure part (b), calculate the maximum shear stress max and the maximum bending stress max (Enter the magnitudes in MPa.) Tmax = MPa MPa max=

Consider a wood beam (see figure) carrying a uniform load of 21.5 kN/m (which includes the weight of the beam). The length is 2.25 m and the cross section is rectangular with width 150 mm and height 300 mm. 21.5 kN/m 300 mm 150 mm 2.25 m (a) 21.5 kN/m 2.25 m (b) (a) If the beam is simply supported as in figure part (a), calculate the maximum shear stress max and the maximum bending stress max (Enter the magnitudes in MPa.) = max MPa MPa max = (b) If the beam has a sliding support at right as in the figure part (b), calculate the maximum shear stress max and the maximum bending stress max (Enter the magnitudes in MPa.) Tmax = MPa MPa max=

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

2- For the beam in Figure below. a- Compute the immediate deflection produced by total load, b- Estimate the additional long-term deflection if the live load acts continuously. fe = 28 MPa, fy= 400 MPa. 手 Dead Load=27 kN/m Live Load =30kN/m 150 735 250 500 6 m 125 125 150 As=4 Ø 25mm
solve using NSCP 2015limitations/specifications. Show your detailed solution.
A 5-m long simply supported timber beam carries a uniformly distributed load of (12k N/m), as shown in Figure. Determine the maximum compression bending stress that occurs in the beam at any location within the span length.USE (I= *.225x 106 mm 4) 12 kN/m 300 mm 60 mm 110 mm 5 m 100 mm 150 КPа О 25 MPa 41 MPа О 85 MPа О
Solve asap
A 1-meter-long, simply supported copper beam (E = 117 GPa) carries uniformly distributed load q. The maximum deflection is measured as 2.5 mm. (Use available deflection formulas. All beams have constant flexural rigidity EI.) (a) Calculate the magnitude of the distributed load q (in kN/m) if the beam has a rectangular cross section (width b = 25 mm, height h = 50 mm). kN/m (b) If instead the beam has circular cross section and q = 500 N/m, calculate the radius r (in mm) of the cross section. Neglect the weight of the beam. mm
Figure 1 shows a simply supported beam with a concentrated force P applied at the mid-span, B. Given the modulus of elasticity is E = 210GPa. To reduce the displacement of the system, a vertical spring with spring constant ks is installed at B as shown in the figure. P 1 m I= 2.5 x 10-4 m4 B 1 m Figure 1 C k = 2 × 108 N/m7IIIIT
P Flag question A beam shown in figure below, is supported by pin at A and roller at B. Determine the support reaction forces. 20 kN w = 40 kN/m 150 kN-m B- 8 m 3 m Paragraph В I
For the beam in Figure below. a- Compute the immediate deflection due to total load. b- Estimate the long-term deflection assume 30 % of live load as sustained. fc' = 28 MPa, fy= 400 MPa. D.L 10 kN/m www L.L 30 kN/m D.L= L.L= 2.5 m 700 mm ho bo bw bo 350 mm L www 200 mm 4025 ho 250 mm -bw - d 620 mm
The beam as shown in Figure has a rectangular section with a depth of 250mm and width of 40mm. In addition to the point loads, the beam is also subjected to UDL having a magnitude of 176N/m acting at span from point B to free end. Calculate the slope and deflection at free end. Assume E = 200GPa. (Where P =88 KN )
Q.1 Compute the value of deflection at mid-span for the beam loaded as shown in figure below. Given as E = 10 GPa and = 4.5 x 10° mm*. 300 N/m 2 m 2 m R R2 Answer - 100 тт
05. Consider the deformable pin-jointed truss with loading, geometry and section properties as shown in the Figure Q5. Given that E=2x10"N/m, A=10mm, L=Im and P-lkN. The horizontal displacement of Joint C (in mm, up to one decimal place) is „JointC P 2AE 7. AE AE Figure 05
If beam as shown in Figure has a rectangular section with a depth of 100mm and width of 20mm, calculate the slope and deflection at free end. Assume E = 200GPa. where P= 25