Consider a wall that consists of two layers, A and B, with the following values: kA = 0.8 W/m⋅ºC, LA = 8 cm, kB = 0.2 W/m⋅ºC, LB = 5 cm. If the temperature drop across the wall is 18ºC, the rate of heat transfer through the wall per unit area of the wall is a. 89.6 W/m2 b. 72.0 W/m2 c. 153 W/m2 d. 51.4 W/m2 e. 180 W/m2

Consider a wall that consists of two layers, A and B, with the following values: kA = 0.8 W/m⋅ºC, LA = 8 cm, kB = 0.2 W/m⋅ºC, LB = 5 cm. If the temperature drop across the wall is 18ºC, the rate of heat transfer through the wall per unit area of the wall is a. 89.6 W/m2 b. 72.0 W/m2 c. 153 W/m2 d. 51.4 W/m2 e. 180 W/m2

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Determine R if the equivalent spring stiffness constant (keq) of the spring system is 250 N/m
A hot fluid (60° C) flows inside an copper tube with 1.7 cm OD and 1.5 cm ID. The inside of the pipe has a heat transfer coefficient of 130 W/m2-K. The tube is exposed to a room with air and surrounding walls of 23° C. The heat transfer coefficent between the outside of the walls and the room air is 15 W/m2 K. Draw an equivalent circuit diagram of the heat transfer, and quantify the resistance to heat flow by each of the two convective processes, conduction in the tube, and radiation between the outside of the tube and the room walls. Are any of the resistances negligible to the overall heat transfer, and if so, which ones?
Figure below shows the power consumption of a certain household in 1 day. Calculate the total energy consumed in kWh
The subject is Mechanics of Deformable Bodies
A house, for cooling purposes, consists of two zones: the atric area zone A and the living area zone B (see below figure). The living area is cooled by a 2 -ton air conditioning unit that removes 23,000 Btu/hr. The heat capacity of zone B is 1/6 °F per thousand Btu. The time constant for heat transfer between zone A and the outside is 3ℎr, between zone B and the outside is 6ℎr, and between the two zones is 6ℎr. If the outside temperature stays at 90°F, how warm does it eventually get in the attic zone A ?
The inside wall of a furnace is at 2100oF and the outside wall is at 300oF. The wall of a furnace must be designed to transmit no more than 220 Btu/hr-ft2. Two types of bricks are available for construction:TYPE A: k = 0.38 Btu/ hr-ft-R with an allowable maximum temperature of 1400oFTYPE B: k = 0.98 Btu/ hr-ft-R with an allowable maximum temperature of 2300oF Both types of bricks have the same dimensions (9” x 4.5” x 3”) but the cost for Type B brick is twice the cost of Type A brick. Illustrate the order of arrangement of bricks A and B in the furnace wall (with thickness, estimated temperatures at the interface between walls A and B and at the interior and exterior surface, the transport area and direction of transfer included)
A firearm can be modeled as a kind of heat engine, where the projectile acts as a piston that separates from the rest of the system during expansion. Consider a rifle with a 1.70 kg barrel made of iron [specific heat = 448 J/(kg °C)]. The rifle fires a 4.00 g bullet that exits the barrel with a speed of 350 m/s. When the propellant is ignited, 1.10% of the energy released goes into propelling the bullet (this is the thermal efficiency of the "engine"). The other 98.9% can be approximated as being entirely absorbed by the barrel, which increases in temperature uniformly for a short time before this energy is dissipated into the surroundings. What is this temperature increase (in °C)? (Round your answer to at least one decimal place.) °℃
A refrigerator has a coefficient of performance of 2.50, requires 150 W of electrical power to operate, and maintains a temperature of -4.00 °C within its interior compartment. How long would it take to cool a dozen 1.00 L of water in a plastic wrapper from 33.0 °C to -4.00 °C in this refrigerator? Any heat escaping the plastic should be ignored. Remember that 1.00 g/cm3 is the density of water.
A large plate of 0.5 m thickness and constant thermal conductivity of k=60 W/m⋅K in which heat is generated uniformly at a rate of 2 kW/cm3. One side of the plate is heavily insulated so that there is no heat loss from the insulated side of the plate. The other side of the plate is exposed to the environment at T∞= 25oC with convection heat transfer coefficient is 20 W/m2⋅K. a) Express the differential equation and the boundary conditions for steady operating conditions. b) Determine the variation of temperature in the plate. c) Find the inner and outer surface temperatures of plate