Consider a wall of thickness 50 mm and thermal conductivity 14 W/m.K, the left side (x-0) is insulated. Heat generation (q) is present within the wall and the one dimensional steady-state temperature distribution is given by T(x) = ax +bx+c [°CJ, where c = 200 °C, a = -1144 °C/m is the heat fluxes at the right side, x L, (kW/m)? ,b=needs to he determined, and x is in meters. What 9, K 4L) Insulation

Consider a wall of thickness 50 mm and thermal conductivity 14 W/m.K, the left side (x-0) is insulated. Heat generation (q) is present within the wall and the one dimensional steady-state temperature distribution is given by T(x) = ax +bx+c [°CJ, where c = 200 °C, a = -1144 °C/m is the heat fluxes at the right side, x L, (kW/m)? ,b=needs to he determined, and x is in meters. What 9, K 4L) Insulation

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Please show all work clearly
Obtain the mathematical model of the thermal system in Fig. 1. Note: Consider the heat transmitted by convection q1(t) and q2(t), and the heat given by a resistance q(t). dT1(t) (a) Variation of heat inside d(t) dT2(t) (b) Variation of heat in the wall d(t) Та T2 T1 min q1 A1 A2 Fig.1 Consider p1, p1, and Cp1, Cp2 constants. U1 and U2 are overall heat transfer coefficients, which are constants. As is the surface area for heat losses to ambient. T1> Ta and T2> Ta (inlet temperatures are higher than ambient temperature).
Just solve the last point(c)
Pls handwrite
Find the heat transfer per unit area through the composite wall. Assume one-dimensional heat flow
A house, for cooling purposes, consists of two zones: the attic area zone A and the living area zone B (see below figure). The living area is cooled by a 2-ton air conditioning unit that removes 19 °F per thousand Btu. The time constant for heat 4 41,000 Btu/hr. The heat capacity of zone B is transfer between zone A and the outside is 2 hr, between zone B and the outside is 4 hr, and between the two zones is 4 hr. If the outside temperature stays at 90°F, how warm does it eventually get in the attic zone A? It eventually gets to be F in the attic zone A. (Type an integer or decimal rounded to the nearest hundredth as needed.) 4 hr Î A 쉽 4 hr B 2 hr 41,000 Btu/hr
Unit of thermal conductivity in S.I. units is(A) J/m² sec(B) J/m °K sec(C) W/m °K(D) Option B and C above.
A metallic plate, whose external faces are kept at temperatures T1 and T2 by a cooling fluid, has a thin-thickness resistance heater with thermal flux equal to o, as shown in the following figure. T, т, 9cond gcond - L + L The differential energy balance of this plate, in Cartesian coordinates, can be expressed by ôT pcp dy (" dy where r is the material's specific mass, cp is the material's specific heat, T is the temperature, t is the time, and x, y, z are the variables on the Cartesian axes. Consider the heat flux of this one-dimensional plate in the x direction, the constant thermal conductivity of the material, and steady state operation. Check the equation that describes this phenomenon and explain why your answer a (aT ôz dz pc. 出业姐,业逃】- ()- dz
subject: Thermodynamics
A steady-state electric motor operates under 10 Ampere and 220 Volt operating conditions. The output shaft rotates with 100 rpm (rpm) and 16 Nm torque. The heat transfer from the electric motor to the environment is related to the equation of surface temperature Tb, ambient temperature T0 and hA(Tb-T0). The energy transfer is shown on the figure with the help of arrows. (h=100 W/(m2K)), A= 0.195 m2, T0= 293 K) a) Determine the temperature Tb in K (Kelvin). b) Assuming the electric motor as the system, determine the entropy production in kW/K. c) Assume the area of the system boundary as the ambient temperature (T0) and determine the entropy generation in kW/K for the extended system boundaries.
Find solutions please
Heat at a rate of 5 kW is being uniformly produced in a solid cylinder. The cylinder has a diameter and a length of 2 cm and 4 m, respectively. Find a) the volumetric and the linear heat generation rates for this cylinder and b) heat flux at r = D/2. [Ans.: ģ = 0.25 kW/m, ġ" = 19.9 kW/m², and ġ" = 3979 kW/m³].