Consider a wall made of Material A that is 4.5m long, 3.0m high, and 0.22m thick. The interior and exterior design temperatures are Too1 and Too2, respectively, the heat transfer coefficients on the interior and exterior surfaces are 10 and 20W / m2 •C. If insulating material is placed on the inside surface of the wall to maintain the temperature shallow from it to T1. Determine the required thickness of the insulating material.

Consider a wall made of Material A that is 4.5m long, 3.0m high, and 0.22m thick. The interior and exterior design temperatures are Too1 and Too2, respectively, the heat transfer coefficients on the interior and exterior surfaces are 10 and 20W / m2 •C. If insulating material is placed on the inside surface of the wall to maintain the temperature shallow from it to T1. Determine the required thickness of the insulating material.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

1. A pipe is covered with three insulation layers where the corresponding thicknesses are 150 mm, 250mm and 300mm and the respective thermal conductivities are 3.2 W/m°C, 2.1 W/m°C and 1.5 W/m C. The length of the pipe is 3m. The inner side of the pipe which has a diameter of 300 mm is exposed to a hot gas at 1000 °C with convection coefficient of 50 W/m2°C and the temperature of the inner side of the pipe surface is 800 °C. The air outside the pipe is at 25°C with a convection coefficient of 35 W/m2°C. a. Draw a schematic diagram which shows the heat transfer process b. Calculate the Heat transfer rate c. The overall heat transfer coefficient "U" of the system based on the inner pipe d. Temperature at each of the layers and at the outermost surface of the pipe.
A 1,155 ft², 4 in. thick concrete wall has inside and outside surface temperatures of 24°C and 4°C. A 2 in. insulation batt with a thermal conductivity of k= 0.03 Btu/(h. ft. °F) is added to the wall. Determine the reduction in heat transfer rate. What is the thickness of the insulation in meters? 0.0508 x Your response differs from the correct answer by more than 10%. Double check your calculations. m What is the thermal conductivity value of the insulation batt in W/(m. K)? 0.05188 W/(mK) What is the R-value of the concrete wall (in m². K/W)? 0.022578 X Your response differs from the correct answer by more than 10%. Double check your calculations. m². K/W What is the R-value of the insulation batt (in m² K/W)? 1.9584 X Your response differs from the correct answer by more than 100%. m² K/W What is the heat transfer rate (in W) when the insulation is added? X W What is the percent reduction in the heat transfer rate? 96 x %
The inner diameter of a pipe made of %1 C steel used in the drying machine of a textile factory is D1 = 160 mm and the thread diameter is D₂= 170 mm. The pipe is insulated with 25 mm thick glass wool. The heat transfer coefficient between the air and the pipe surface at 90 °C temperature inside the pipe is 80 W/m²K. The temperature of the ambient air outside the insulation is 20 °C and the air comes perpendicular to the cat wool surface at a speed of 10 m/s. Find the total heat transfer coefficient according to the inside diameter of the pipe. Calculate the heat transfer per unit length of pipe per unit time ?
The exterior wall of a house is composed of a 20 cm thick layer of ordinary brick (conductivity 0.72 W/m K) and a 2.5 cm layer of plaster (conductivity 0.17 W/m K ) on each side (two layers in total). Other purely conductive resistances can be neglected, such as the layer of paint on both sides of the wall. Assume the outer face of the wall is at 35 °C and the inner face is at 20 °C and fill in the gaps. The magnitude of the heat flux through the wall corresponds to the _________ W/m2 and is perpendicular to the wall ________________(fill in with "outside-in" or "inside-out") of the environment. If the wall has a total area of 300m2, the heat transfer rate corresponds to ___________________
Calculate the heat loss through a 100-ft² wall with an inside temperature of 65°F and an outside temperature of 35°F. Assume the exterior wall is composed of 2- in. of material having a 'k' factor of 0.80, and 2-in. of insulation having a conductance of 0.16. RTotal = 8.75 & Q = 342-Btu/hr RTotal = 9.2 & Q = 399-Btu/hr RTotal = 8.75 & Q = 399-Btu/hr RTotal = 9.2 & Q = 342-Btu/hr Hide hint for Question 3 Utilize the (RTotal = 1/C + x1/k1) equation.
A cylindrical pipe is made up of two materials. The inner material A, which has thermal conductivity of ka, has inner radius ra and outer radius re. On the other hand, the outer material B, which has thermal conductivity of kb, has inner radius re and outer radius rb. Contact resistance between the two materials is known to be hc. The temperature at the inner radius of material A (at ra) is Ta, while the temperature at the outer radius of material B (at ri) is T3. Find an expression for the temperature at the inner radius of material B (at r.) in terms of the given variables.
Q30) A 4-mm-diameter and 5-m-long electric wire is tightly wrapped with a l1-mm thick plastic cover whose thermal conductivity isk = 0.2 W/m °C. Electrical measurements indicate that a current of 15 A passes through the wire and there is a voltage drop of 8 V along the wire. If the insulated wire is exposed to a medium at T 30°C with a heat transfer coefficient of h = 15 W/m2 °C, determine the temperature at the interface of the wire and the plastic cover in steady operation. Also determine whether doubling the thickness of the plastic cover will increase or decrease this interface temperature..
A steel pipe with heat transfer coefficient of 42 W/mK contains flowing water. The outer diameter of the pipe is 90 mm and the wall thickness is 3mm. Calculate: i. The heat loss by convection and conduction per meter length of un-insulated pipe when the water temperature is 14°C, the outside air temperature is -10°C, the water side heat transfer coefficient is 30 KW/m^2K and the outside heat transfer coefficient is 20 KW/m^2K. ii. Calculate the corresponding heat loss when the pipe is lagged with insulation having an outer diameter of 200 mm, and thermal conductivity of K = 0.05 W/mK