es!Required informationConsider a truss shown below. Given that F= 0.85 kN.NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part.BD F H JANNAC E GTHIN1m 1m 1m 1 m 1m 1 m2mΑKLFind the force supported by member FH. (Round the final answer to four decimal places. Include a minus sign if necessary.)The force supported by member FH iskN.

Objective: To determine the force in member FH of the given truss. Given: F = 0.85 kN The given…

Consider a truss shown below. Given that F= 0.85 kN. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. B D F H J AWA C E G 2m FY K 1m 1m 1m 1m 1m 1m L Find the force supported by member FH. (Round the final answer to four decimal places. Include a minus sign if necessary.) The force supported by member FH is kN.

Consider a truss shown below. Given that F= 0.85 kN. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. B D F H J AWA C E G 2m FY K 1m 1m 1m 1m 1m 1m L Find the force supported by member FH. (Round the final answer to four decimal places. Include a minus sign if necessary.) The force supported by member FH is kN.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Determine the force in each member of the loaded truss. The force is positive if in tension, negative if in compression. AB= AC = A Answers: BC= 37 53 i i i B 219 kg N Z Z Z N N
Find all the forces components
A beam is shown in the figure below, and the flexural stiffness of the beam section is constant EI:(a) Use the Moment-area Method to find the Slope after point A is deformed.(b) Same as above, try to find the slope of point B after deformation.(c) Same as above, try to find the vertical deflection of point C (Deflection).
A massless beam supports two weights as shown. Find W such that the supporting force at A is zero. L- L 4 4 2 826 N A B W Your answer
Find F(DC), F(DB) and F(BC)
pls help! Write the complete solutions and legibly. Answer in 2 decimal places. UPVOTE WILL BE GIVEN! MECHANICS OF DEFORMABLE BODIES Let Q = 0 and T = 8 (Example: 12Q°C = 120°C). Just substitute the number in letter. Thank you! For the frame shown, a 4QQT-N load is acting on member ABD at D. If the allowable material shear stress for is 4Q MPa, determine the required diameter (rounded off to the nearest 2.5 mm) of the pins at C and D. Pin C and pin D are subjected to double shear and single shear, respectively. If the thickness of member BC is 12 mm and that of member DE is 16 mm, determine the maximum bearing stress at C.
SOLVE STEP BY STEP IN DIGITAL FORMAT Determine by the method of nodes, the forces at which all the members of the following trusses work. Place the results of each force in the members of the truss drawing for qualification. 1200 N 300 N A B oolco 0.00 3 m E 4 m 4 m
Solve for the reaction forces of the given figure from point a to b. pls show your complete solutions. thank you
please solve it using FORCE METHOD. Thank you. only HANDWRITTEN answer needed ( NOT TYPED)
Problem 3: If µs = 0.35 between all surfaces (but pulleys remain frictionless), then find the smallest force P required to move the blocks. P 60 lb B 40 lb
Determine the forces in members BC, BE, and BF. The triangles are isosceles. The forces are positive if in tension, negative if in compression. BC= Answers: BE= 69⁰ G 40° Mi BF = i A 69⁰ 69⁰ F B L L L 69⁰ /69⁰ E C 69⁰ D L
ENGINEERING MECHANICS RATE WILL BE GIVEN! NO LONG EXPLANATION NEEDED! SHOW THE COMPLETE SOLUTIONS. ANSWER IN 4 DECIMAL PLACES.