Consider a steam power plant that operates on a reheat Rankine cycle and has a net power output of 80 MW. Steam enters the high-pressure turbine at 10 MPa and 500°C and the low-pressure turbine at 1.4 MPa and 500°C. Steam leaves the condenser as a saturated liquid at a pressure of 10 kPa. Assume both turbine and compressor are isentropic. Determine the quality (or temperature, if superheated) of the steam at the turbine exit. The quality of the steam at the turbine exit is 1.12

Consider a steam power plant that operates on a reheat Rankine cycle and has a net power output of 80 MW. Steam enters the high-pressure turbine at 10 MPa and 500°C and the low-pressure turbine at 1.4 MPa and 500°C. Steam leaves the condenser as a saturated liquid at a pressure of 10 kPa. Assume both turbine and compressor are isentropic. Determine the quality (or temperature, if superheated) of the steam at the turbine exit. The quality of the steam at the turbine exit is 1.12

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Consider a steam power plant that operates on a simple ideal Rankine cycle and has a net power output of 120 MW. Steam enters the turbine at 10 MPa and 550° c and is cooled in the condenser at a pressure of 15 kPa by running cooling water from a nearby source the condenser at a rate of 3000 kg/s. Determine the enthalpy h4 at the outlet of the Turbine
Consider a steam power plant operating on a simple ideal Rankine cycle. Steam enters the turbine at 15 MPa and 650°C and is condensed in the condenser at a pressure of 15 kPa. Determine the thermal efficiency (%). (Use 2 decimal places for the final answer.)
A vapor-compression cycle is used as a refrigerator to extract 8 kW of heat from a cold space at 0°C and rejects heat into a space at 25°C. R-134a enters the compressor at 140 kPa superheated by 4°C above the saturation temperature and leaves at 900 kPa. It exits the condensor as a saturated liquid. Assume that pressure losses are negligible and that the compressor is isentropic. Report your answers to four significant digits using rounding. QUESTION 1 Report the maximum possible COP. QUESTION 3 Report the power required by the compressor. QUESTION 2 Report the mass flow rate in kg/s. QUESTION 4 Report the COP for the cycle.
Consider a 210-MW steam power plant that operates on a simple ideal Rankine cycle. Steam enters the turbine at 10 MPa and 500°C and is cooled in the condenser at a pressure of 7.5 kPa. Show the cycle on a T-s diagram with respect to saturation lines.
Steam in a reheat Rankine cycle enters the first-stage turbine at 8 MPa and 450°C. The steam leaves this first turbine at 800 kPa as a saturated vapor. The steam is then reheated isobarically back to 450°C before entering the second-stage turbine. At the exit of this second turbine, the steam is at 10 kPa and 50°C. The net power output of this cycle is 20 MW, and the water leaves the condenser as a saturated liquid. You may assume the pump functions isentropically and that there are no pressure losses in the condenser and boiler. Determine C. d. e. MW. Draw this cycle on a T-s diagram. Calculate the isentropic efficiencies of the first- and second-stage turbines. Calculate the thermal efficiency of the cycle. Calculate the mass flow rate of steam, in kg/h. Calculate the rate of heat transfer from the water as it passes through the condenser, in
Consider a 210-MW steam power plant that operates on a simple ideal Rankine cycle. Steam enters the turbine at 10 MPa and 500C and is cooled in the condenser at a pressure of 10 kPa. Assuming an isentropic efficiency of 85 percent for both the turbine and the pump, determine the actual specific enthalpy (kJ/kg) at the boiler inlet. (Use 2 decimal places for the final answer.)
CONSIDER A STEAM POWER PLANT OPERATING ON THE IDEAL REHEAT RANKINE CYCLE. STEAM ENTERS THE HIGH-PRESSURE TURBINE AT 15 MPA AND 600 °C AND IS CONDENSED IN THE CONDENSER AT A PRESSURE OF 10 KPA. ASSUMING THE REHEAT TEMPERATURE IS ALSO 600 °C AND IF THE MOISTURE CONTENT OF THE STEAM AT THE EXIT OF THE LOW-PRESSURE TURBINE IS NOT TO EXCEED 10%, DETERMINE: THE PRESSURE AT WHICH STEAM SHOULD BE REHEATED,
Consider a 210-MW steam power plant that operates on a simple ideal Rankine cycle. Steam enters the turbine at 10 MPa and 500C and is cooled in the condenser at a pressure of 10 kPa. Determine the Qout (kJ/kg).(Use 2 decimal places for the final answer.)
A practical power cycle produces steam from the boiler at 600 kPa and 425°C. The turbine has an efficiency of 90%. The condenser pressure is 100 kPa, and the pump operates ideally (i.e., isentropically). Determine the following: (a) the work output from the turbine per kg of steam.(b) the thermal efficiency of the cycle.(c) the maximum possible efficiency of the cycle.There are three answers: (a), (b), and (c). Other values must be taken from Perry's handbook. I am sorry if this will take a lot of your time. But I will upvote as a appreciation for your effort
Consider a steam power plant that operates on the ideal reheat Rankine cycle. The plant maintains the boiler at 8000 kPa, the reheat section at 1000 kPa, and the condenser at 20 kPa. The mixture quality at the exit of both turbines is 90 percent. Determine (a) the temperature at the inlet of each turbine, (b) the cycle's thermal efficiency, efficiency of this cycle. Assume a source temperature of 1500 K and a sink temperature of 295 K. (d) the second-law