Consider a steam power plant that operates on the ideal reheat Rankine cycle. The plant maintains the boiler at 8000 kPa, the reheat section at 1000 kPa, and the condenser at 20 kPa. The mixture quality at the exit of both turbines is 90 percent. Determine (a) the temperature at the inlet of each turbine, (b) the cycle's thermal efficiency, efficiency of this cycle. Assume a source temperature of 1500 K and a sink temperature of 295 K. (d) the second-law

Consider a steam power plant that operates on the ideal reheat Rankine cycle. The plant maintains the boiler at 8000 kPa, the reheat section at 1000 kPa, and the condenser at 20 kPa. The mixture quality at the exit of both turbines is 90 percent. Determine (a) the temperature at the inlet of each turbine, (b) the cycle's thermal efficiency, efficiency of this cycle. Assume a source temperature of 1500 K and a sink temperature of 295 K. (d) the second-law

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Consider a steam power plant that operates on a simple ideal Rankine cycle and has a net power output of 120 MW. Steam enters the turbine at 10 MPa and 550° c and is cooled in the condenser at a pressure of 15 kPa by running cooling water from a nearby source the condenser at a rate of 3000 kg/s. Determine the enthalpy h4 at the outlet of the Turbine
Consider a steam power plant operating on a simple ideal Rankine cycle. Steam enters the turbine at 15 MPa and 650°C and is condensed in the condenser at a pressure of 15 kPa. Determine the thermal efficiency (%). (Use 2 decimal places for the final answer.)
A simple ideal Rankine cycle with water as the working fluid operates between the pressure limits of 10 MPa in Boiler the boiler and 10 kPa in the condenser and a turbine inlet temperature of 500°C. The boiler is sized to provide a steam flow of 165 kg/s. Determine: (a)(s) the quality of the steam at the turbine exit, (b) the thermal efficiency of the cycle, and (c) 2) the net power produced by the cycle Wa Condesser Turbine
A power plant uses a gas turbine to produce electricity. Assume that the gas-turbine operates on the ideal Brayton cycle has a pressure ratio of 8. The outside air temperature is 27 C and without preheating, the air is drawn into the compressor. The air compressed in the compressor and its pressure and temperature increase. Thereafter it is supplied into the combustion chamber where its temperature increases to 1023 C at constant pressure. Thereafter, hot air is drawn into the turbine. By considering the air-standard assumptions, determine (a) the gas temperature at the exits of the compressor and the turbine (b) the back work ratio (c) the thermal efficiency
Thermodynamics question Consider a steam power plant operating on the simple ideal Rankine cycle. Steam enters the turbine at 3 MPa and 350 °C and is condensed in the condenser at a pressure of 10 kPa. If line number 1 is saturated liquid and assuming 100% isentropic efficiency of the turbine and the pump. Determine: A-work produced in the turbine per unit mass, B-The thermal efficiency of this cycle, C-The heat lost from the condenser, D-maximum possible efficiency of the cycle.
Scenario (1) The first steam power plant operates on an ideal reheat Rankine cycle. Steam enters the first turbine at 8 MPa and 500 C and leaves at 3 MPa. Steam is then reheated at a constant pressure to 500 C before it expands to 20 kPa in the low-pressure turbine. Assuming that heat is being added to the boiler from a high temperature source at 1800 K and the condenser is transferring heat to a temperature sink at 300 K. Task 1 Investigate the effect of changing pump efficiency on the overall thermal efficiency of the thermodynamics cycle (Hint: You will assume different values for the isentropic pump efficiency such as: 70%, 80%, 90%, 95%, and 100%, then observe how it will change the thermal efficiency of the cycle). Representing the results in a plot is recommended.
Scenario (1) The first steam power plant operates on an ideal reheat Rankine cycle. Steam enters the first turbine at 8 MPa and 500 C and leaves at 3 MPa. Steam is then reheated at a constant pressure to 500 C before it expands to 20 kPa in the low-pressure turbine. Assuming that heat is being added to the boiler from a high temperature source at 1800 K and the condenser is transferring heat to a temperature sink at 300 K. Task 1 Investigate the effect of changing turbine efficiency on the overall thermal efficiency of the thermodynamic cycle. (Hint: You will assume different values for the isentropic turbine efficiency such as: 70%, 80%, 90%, 95%, and 100%, then observe how it will change the thermal efficiency of the cycle). Representing the results in a plot is recommended.
Consider a 210-MW steam power plant that operates on a simple ideal Rankine cycle. Steam enters the turbine at 10 MPa and 500C and is cooled in the condenser at a pressure of 10 kPa. Determine the Qout (kJ/kg).(Use 2 decimal places for the final answer.)
A simple Rankine cycle uses water as the working fluid. The boiler operates at 6400 kPa and the condenser at 70 kPa. At the entrance to the turbine, the temperature is 490 °C. The isentropic efficiency of the turbine is 84 %, pressure and pump losses are negligible, and the water leaving the condenser is subcooled by 6.7 °C. The boiler is sized for a mass flow rate of 18 kg/s. Determine the following values. (1) The temperature at the pump inlet. / 80.3 (2) The specific volume at the pump inlet. (3) The specific enthalpy at the turbine exit. X 346 (4) The rate at which heat is added in the boiler. (5) The power required to operate the pumps. (6) The net power produced by the cycle. (7) The thermal efficiency. o °C O m/kg O kJ/kg O kW O kW O kW 0.001030
The digital thermometers that we use in the lab today are similar to the ones that we use in our homes, but several years ago scientists used to use glass thermometers that contained a thin column of mercury to measure temperature. Why do you think we no longer use the mercury thermometers in the lab?
A steam power plant operating in a Rankine cycle has saturated yapor at 4.0 MPa leaving the boiler. The turbine exhausts to the condenser, operating at 75 kPa, and the mass flow rate of the working fluid is 5.0 kg/hr. The turbine efficiency is 0.85. Solve for the work produced by the turbine and the pump (in Watts), the heat transfer in the boiler (in Watts), and the Rankine cycle efficiency.
Consider a 210-MW steam power plant that operates on a simple ideal Rankine cycle. Steam enters the turbine at 10 MPa and 500°C and is cooled in the condenser at a pressure of 7.5 kPa. Determine the thermal efficiency of the cycle. The thermal efficiency of the cycle is 59.6 %.