Consider a point in a structural member that is subjected to plane stress. Normal and shear stresses acting on horizontal and vertical planes at the point are shown. If oy 18 ksi, determine the principal stresses acting at the point. 15 ksi 4 ksi 18.31 ksi and -8.65 ksi 27.78 ksi and -12.42 ksi 25.60 ksi and -11.60 ksi 20.57 ksi and -9.57 ksi O 35.70 ksi and -16.21 ksi

Consider a point in a structural member that is subjected to plane stress. Normal and shear stresses acting on horizontal and vertical planes at the point are shown. If oy 18 ksi, determine the principal stresses acting at the point. 15 ksi 4 ksi 18.31 ksi and -8.65 ksi 27.78 ksi and -12.42 ksi 25.60 ksi and -11.60 ksi 20.57 ksi and -9.57 ksi O 35.70 ksi and -16.21 ksi

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

At a point in a stressed body, the known stresses are o, = 16 ksi (T), ơy 11 ksi (T), o, = 12 ksi (T), Ty 3 ksi, Tyz = -2 ksi, and t,r = 0. Determine (a) the normal and shear stresses on a plane whose outward normal is oriented at angles of 38°, 64°, and 64.39° with the x, y, and z axes, respectively. (b) the principal stresses and the absolute maximum shear stress at the point. Determine the three orthogonal components of the resultant stress. Answers: Sx = ksi Sy = i ksi Sz = i ksi
Answer proplem 1,3 and 1.4
QUESTION 3) A horizontal beam AD is supported by an inclined strut CB and carries a load of 15 kN at joint D in the figure. The strut, which consist of two bars each of thickness 40 mm, is connected to the beam by a rivet passing through the three bars meeting at joint C. The allowable shear stress and bearing stress are t-60 MPa and o=120 MPa, respectively. a) Determine the required diameter of the rivet at the hinge C that carry safely by the given system. b) If the diameter rivet used on the support A is 20 mm check whether this rivet diameter is sufficient for the given system. 0.8m Im 0.6m 15 kN В Beam AD 20mm Strut CB 40mm 100mm 40mm 50mm 100mm Detail of joint C Detail of joint A
Check the cross-section for bending if the allowable normal stress is o =±120 MPa. a: + + 1 = 4 m a = 15 cm q = 3 kN/m a +
Consider a point in a structural member that is subjected to plane stress. Normal and shear stress magnitudes acting on horizontal and vertical planes at the point are Sy-17 MPa, S, - 60 MPa, and Swy- 29 MPa. (a) Draw Mohr's circle for this state of stress. (b) Determine the principal stresses (ơp > op2) and the maximum in-plane shear stress Tmax acting at the point. (c) Find the smallest rotation angle 0, (counterclockwise is positive, clockwise is negative) that will rotate to principal directions. Then show these stresses in an appropriate sketch (e.g, see Figure 12.15 or Figure 12.16) Say Answers: MPa. Opl = MPa. MPa. Tmax = 0, =
In the Figure 5, the normal stress on the cross- sectional area is (in Mpa): Figure 5: у P = 400 KN X 30 mm 1000 mm 30° Area 20 mm الاختيارات 577 O 597 587 O 567
The stresses shown in the figure act at a point on the free surface of a machine component. If o = 22.4 ksi in the direction shown, determine the shear stress Txy at the point. Txy O 14.48 ksi 11.51 ksi O 13.53 ksi O 10.63 ksi O 8.84 ksi 5.0 ksi 24° 2.8 ksi
Q.2 A force F is applied to a rigid beam AB. The diameter of the deformable 2х X post AC is 20 mm and diameter of the deformable post BD is 10 mm. A B F= 60 (kN) and x = 1.2 (m) E=70 GPa for the posts AC and BD. 1m 1m C Calculate the followings a) Normal stresses at post AC and BD b) Normal strains at post AC and BD c) Deformations at post AC and BD d) Angle of tilt that occurs in Beam AB.
a.)For the given figure, determine the normal stress in MPa at segment AB, Cross-section of AB is 1500mm2. b.)Determine the normal stress in MPa at segment BC. Cross-section of BC is 2000mm2. c.)Determine the normal stress in MPa at segment CD, Cross-section of CD is 1200mm2.
finding the principle stresses and stress concentration, bending stress, shear stress D D= 0. 375in lin F MA t. 2in F=200lb, W=100lb at the bend