Consider a point in a structural member that is subjected to plane stress. Normal and shear stresses acting on horizontal and vertical planes at the point are shown. If a = 9 MPa in the direction shown, determine the magnitude of the maximum in-plane shear stress at the point.

Q: A. Draw the shear and moment diagram of the loadings below using area method. 20 kN/m 20 KN 10 kN/m…

A:

Q: 11. The cable supports = 10 kN/m. Determine the tension in the cable at each pport A and B. the…

A: The tension is generally the cable that leads to the forces pulling on the cable from either end. It…

Q: Problem 5 Angles AOB, BOC, and COD are measured on the same angle at point O. Determine the most…

A: GIVEN : Measurement of Angles, number of measurements. REQUIRED : Most probable Angle, MPV

Q: 3. A barometer at the top of the mountain 1300 ft. above sea level reads 780 mm of mercury. What is…

A:

Q: Subject: Solving for moments of inertia I am working on my review for my final. I am having…

A: Note: Hi! Thank you for the question As per the honour code, We’ll answer the first question since…

Q: 9. The thin-walled tube is subjected to an axial force of 40 kN. If the tube elongates 3 mm and its…

A:

Q: B. A truck with axle loads of 30 kN and 500 kN on a wheel base of 4 m rolls across a 8-m span.…

A:

Q: A tee section is made up of a 30 mm x 150 mm flange and a 30 mm x 160 mm web. Determine the…

A:

Q: 5. In the figure, fluid A is water and fluid B is mercury. Compute the difference in pressure head…

A: To find pressure difference between m and n in terms of feet of water

Q: Problem 1: Using virtual work method, find the deflection and at free end when EI is rotation…

A: Given data:

Q: The compound shaft, compose of steel, aluminum, and bronze segments, carries the two torques shown…

A:

Q: Write true if the statement is correct. if the statement is wrong, Write the word or phrase that…

A:

Q: From Figure 1 shown below, Determine the following (Absolute value): A Than 5.00 meter W- 37.09-…

A:

Q: Consider that a built-up section shown in the figure below is used for the beam loaded with 10 kN/m…

A: As per the bartleby guidelines only 3 subparts can be solved, Please repost the question for other…

Q: If the hydraulic cylinder AB is extending at a constant rate of 1 ft/s, determine the dumpster's…

A: Given: Hydraulic cylinder AB extending at constant rate, V= 1 ft/s  To find out Angular velocity…

Q: Mohr's circle is shown for a point in a physical object that is subjected to plane stress. If 1 grid…

A: Given I grid square = 7MPa

Q: Please

A: A universal law is something that is valid to everyone such as Pappus law, law of conservation of…

Q: A mercury barometer at the base of the mountain reads 423 mm. F same time, another barometer at the…

A: Reading at the base of mountain (hb) = 423mmReading at top of mountain (ht) = 423mm

Q: eigning N each form part of the retaining wall of a swimming pool. 300 540 540 Plastic mm liner…

A: First, check the A and B for both the slide and tip They find the overturning and resisting moment…

Q: Determine the ultimate or the factored moment capacity oMn of the beam cross section shown if fc' =…

A: b = 350 mm h = 600 mm cover = 70 mm Steel reinforcement: 3-#25mm fc = 28 MPa fy = 275 MPa

Q: A pin-connected structure is supported and loaded as shown. Member ABCD is rigid and is horizontal…

A: Given, E = 30,000 ksi A = 1.25 in2  σ1 = 18 ksi

Q: Find the bulk specific gravity of a Reclaimed Asphalt Pavement (RAP) if the measured asphalt binder…

A: Given: The asphalt binder content is 4.2%. The specific gravity of the asphalt binder is 1.04. The…

Q: State the assumption in Dupuiť's solution. Show that using this assumption, Casagrande's confocal…

A: Introduction- About engineering piqued his interest in economics, which he self-taught. His 1844…

Q: Given the laboratory results of the Atterberg Limit Test, plot the water content versus the number…

A:

Q: Solve the area using DPD method. LENGTH (L) BEARINGS IN "W.C.B LINE BEARINGS (0) AB 522.1 N 43° 50'…

A: To Compute Area of the lot using DPD Method.

Q: Problem II. Frictionless, incompressible, one dimensional flow of the water passes through the…

A: Given,

Q: Problem 2: Given the following elements of a circular curve: length of long chord = 70 m; middle…

A: Length of long chord=70m To find degree of curve

Q: 4. Specific Weight is also called Relative Density. 5. Standard density of water in English unit is…

A: 4, false Because specific weight=weight of fluidvolume of fluid=mgv=Density × acc due to gravity…

Q: Determine the resultant of B and C if the resultant of A and B is 100 kN directed along the z-axis.

A: Given, Resultant of A and B =100 kN

Q: PROBLEM 3: The square footage of several thousand apartments in a new development is advertised to…

A: Solution : The null and alternative hypothesis is , This will be a left tailed test because the…

Q: A sewage lagoon that has a surface area of 12.5 ha and a depth of 1.38 m is receiving 8200 m³/d of…

A: A = 12.5 ha d = 1.38 m Q = 8200 m3/d Co = 190 mg/L C = 25 mg/L

Q: A lever is attached to a shaft with a square shear key as shown. The force applied to the lever is P…

A:

Q: 7. A particle travels along a straight-line path such that in 4secs it moves from an initial…

A:

Q: Mohr's circle is shown for a point in a physical object that is subjected to plane stress. Each grid…

A:

Q: 1. From a known point V (vertex), the tangent lines of a compound curve are drawn - having azimuths…

A: Given Compound curve with azimuth of back, common & forward tangent    To Determine a. Radius of…

Q: An aluminum [E = 8600 ksi] bar is bonded to a steel [E = 30150 ksi] bar to form a composite beam as…

A:

Q: determine the single resultant load in the z direction that would produce the same e original…

A:

Q: The rigid beam BC is supported by rods (1) and (2). The cross-sectional area of rod (1) is 9 mm².…

A:

Methods to Determine Vertical Stress

The load applied to the soil is transferred to the underground. The presence of water at soil pores and solid grains above the soil are the primary components that are responsible for the effective load transfer. Due to the load acting, the internal component of the soil or the underground formations undergoes deformations or a tectonic shift. The amount of deformation depends upon the amount of load acting on the soil surface, which indeed, depends on the weight of everything present above the soil. Due to this, the underground soil element develops internal stresses which try to resist the tectonic changes.