) Consider a double - fluid manometer attached to an air pipe shown in Figure. If the specific gravity of one fluid is 13.55, determine the specific gravity of the other fluid for the indicated absolute pressure of air. Take the atmospheric pressure to be 100 kPa. ( Consider a double-fluid manometer attached to an air pipe sho wn in Figure. Ifthe specific gravity of one fluid is 13.55, determine the specific gravity of the otherfluid for the indicated absolute pressure of air. Take the atmospheric pressure to be100 kPa.AirP= 76 kPa40 cmSG222 cmSG = 13.55

Specific gravity is defined as the ratio of the density of the substance to the density of the…

Consider a double-fluid manometer attached to an air pipe shown in Figure. If the specific gravity of one fluid is 13.55, determine the specific gravity of the other fluid for the indicated absolute pressure of air. Take the atmospheric pressure to be 100 kPa. Air P= 76 kPa 40 cm SG2 22 cm SG, = 13.55 %3D

Consider a double-fluid manometer attached to an air pipe shown in Figure. If the specific gravity of one fluid is 13.55, determine the specific gravity of the other fluid for the indicated absolute pressure of air. Take the atmospheric pressure to be 100 kPa. Air P= 76 kPa 40 cm SG2 22 cm SG, = 13.55 %3D

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Find the mass of Liquid 1,2,3,4 and the density of the liquid for liquid 1,2,3,4
Q1 A U-tube manometer is used to measure the pressure of oil of specific gravity 0.85 flowing in a pipe line. Its left end is connected to the pipe and the right-limb is open to the atmosphere. The centre of the pipe is 100 mm below the level of mercury (specific gravity- 13.6) in the right limb. If the difference of mercury level in the two limbs is 160 mm, determine the absolute pressure of the oil in the pipe. Liquid (5,-ERS) Pips
A pressurized tank contains water with some air above it. As shown on figure below. Multi-fluid manometer is used to determine the pressure at the air-water interface ( If hi= 0.7 m, hz=0.4 m, h3=D0.55 m and ha = 0.85 m. Also, specific gravity of water = 1 and specific gravity of crude oil = 1.8 and specific gravity of mercury 12.5 and specific gravity of shale oil = 2.5 Determine the absolute pressure at point 5 in Pascal unit. [Given: g =9.81 m/s2 and atmospheric pressure 101300 Pa] Mercury S.G. 125 Water S.G. -1 he Crude oil S.G. 18 Shale oil S.G. 25
The pressure drop of water in a pipe is measured by a manometer using a liquid of density 2000 kg/m³. The difference in height of the liquid in the limbs is 10 cm. Then, the pressure drop is
The Venturi meter shown in the sketch below, contracts the flow down to one quarter of its original area. Cold air at 0 deg C flows in the pipe through the Venturi meter. The velocity of the air upstream of the Venturi meter is equal to 40 ft/s and the pressure at the same point is equal to 30 psia. What is the manometer reading if the fluid of the manometer is water with density 1000 kg/m3 . Assume that the air behaves as an ideal gas with molecular weight equal to Mw=29 kg/kmol and constant density evaluated at upstream conditions. Use Bernoulli's equation for your calculations. please respond asap!
1. The reading of an automobile fuel gage is proportional to the gage pressure at the bottom of the tank. The tank is A deep and is contaminated with B of water. The specific volume of gasoline is 0.00147076 m /kg and that of air is 0.0008313 m³/kg. Unit weight of water is 9790 N/m3 a. Determine the gage reading when the tank is full of gasoline b. How many cm of air remains at the top when the gage indicates full if the tank is A deep and is contaminated with B of water. c. Determine the pressure at the interface of the gasoline and water when the gage indicates full A = First name in inches Vent B = A/10 in inches Air h A Gasoline Pgage Water B
A venturimeter as shown in the figure (not to scale) is connected to measure the flow of water in a vertical pipe of 20 cm diameter. Pipe diameter = 20 cm Throat diameter = 10 cm 30 cm T 15 cm Mercury specific gravity = 13.6 Assume g = 9.8 m/s². When the deflection in the mercury manometer is 15 cm, the flow rate (in lps, round off to two decimal places) considering no loss in the venturimeter
The figure shows two closed spaces filled with air, so if the barometer reading is equal to 750mmHg, the external manometer reading is 25 mmHg, and the scale A reads the pressure 200 kpa What will the reading of the inner manometer (x) be? Note that the standard density of mercury is equal to 13.56 Patm Air U FU 25 Air 200 Kpa
In the figure shown, originally there is a H2=9 cm manometer reading and H1=15 cm. Atmospheric pressure is 101.3 kPa. what is the absolute pressure at A (kPa)? If the absolute pressure at A is doubled, what then would be the manometer reading (cm) ?
You are required to design a barometer that uses water instead of mercury to operate under standard sea-level conditions. Draw a conceptual diagram of your barometer design. Show on your diagram what the pressures will be at all liquid-gas interfaces, and where the barometer reading will be taken.Calculate the minimum height requirement of the barometer tube to measure standard sealevel atmospheric pressure.