Consider a cylindrical specimen of a steel alloy 8.3 mm (0.3268 in.) in diameter and 84 mm (3.307 in.) long that is pulled in tension. Determine its elongation when a load of 21640 N (4865 lb;) is applied. The tensile stress-strain behavior for this steel alloy is shown in the Animated Figure 6.22.

Consider a cylindrical specimen of a steel alloy 8.3 mm (0.3268 in.) in diameter and 84 mm (3.307 in.) long that is pulled in tension. Determine its elongation when a load of 21640 N (4865 lb;) is applied. The tensile stress-strain behavior for this steel alloy is shown in the Animated Figure 6.22.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The principal plane stresses and associated strains in a 35 ksi, 02 = 15 ksi, plane at a point are 01 1 €1 = 1.02(10-3), 2 = 0.180(10-³). ▼ Determine the modulus of elasticity. Express your answer using three significant figures and include the appropriate units. E= Submit Part B V= μA Value Request Answer Submit Determine the Poisson's ratio. Express your answer using three significant figures. ΠΑΠΙ ΑΣΦ | Η VE Units Request Answer ? vec POSSIA space ?
PROBLEM 4. The rigid bar is supported by a pin at A and two metal wires, each having a diameter of 4 mm. The stress-strain diagram of the steel is given in the Figure below. The lower graph is the zoomed view of the elastic deformation and yielding phases of the stress-strain diagram given by the upper graph (a) Obtain the Young's modulus of metal. What can you say about the kind of metal considering the Young modulus? If the point G is displaced 1.5 mm in vertical direction, (b) determine the forces at wires EB and DC, (b) the intensity of the distributed load w, (c) the final diameters of wires. (Poisson's ratio is v-0.3) E D o (MPa) 600 500 800 mm 400 300 G. 200 10 W 400 mm 250 mm- e(mm/mm) 150 mm 0.04 0.08 0.12 0.16 0.20 0.24 0.28 00005 00010.0015 Q002 00025 0,003 00035
Determine the elastic tensile load "F" that acts on mild steel specimen of Diameter 8 mm & Modulus of Elasticity 201 GPa. It is found that the specimen has undergone an extension of 1.6 mm due to the elastic load "F". Also, determine the length "L" of the specimen, if the strain-induced due to the load "F" on the specimen is 4.1 x 10-3. Solution Cross-sectional Area, A (in mm²) Tensile Load, F (in N) Length of the Specimen (in mm)
A circular aluminum alloy [E = 70 GPa; a = 22.5 x 10-6/°C; v = 0.33] pipe has an outside diameter of 245 mm, a wall thickness of 15 mm, and a length of 4.5 m. The pipe supports a compressive load of 610 kN. After the temperature of the pipe drops 49°C, determine: (a) the axial deformation of the pipe. (b) the change in diameter of the pipe. Answer: (a) 8 = i AD= i mm mm
Determine the elongation of an aluminium hollow cylinder of an inner diameter of 1.22 cm & the external diameter of 23.4 mm is subjected to an elastic tensile load of 228 kN. Take the elastic modulus of the aluminum specimen as 71 GPa and the initial length of the hollow cylinder as 187 mm. Solution: i) Cross-sectional Area (in mm2) = ii) Stress-induced (in N/mm2) = iii) Strain-induced (at least 3 decimal places accuracy)= iv) Elongation (in mm) =
Determine the elastic tensile load "F" that acts on mild steel specimen of Diameter 9 mm & Modulus of Elasticity 205 GPa. It is found that the specimen has undergone an extension of 1.7 mm due to the elastic load "F". Also, determine the length "L" of the specimen, if the strain-induced due to the load "F" on the specimen is 3.7 x 10-3. Solution Cross-sectional Area, A (in mm2) Tensile Load, F (in N) Length of the Specimen (in mm)
100 mm must elongate only 5 mm when a tensle load of 100,000 N is applied. Under these A cylindrical specimen of a brass alloy having a circumstances what must be the radius of the specimen? Consider this brass alloy to have the stress-strain behavior shown in Figure below. Tensile strengh 450 MPa (65,000 p A00 10 pu 300 200- 30 Yield strength 250 MPa (36,000 psi 2아 100 1아 100 0.005 0.20 0.30 0.40
A steel column is a cylinder 6.8 m long and 0.35 m in diameter. What is the change in length of the column when it experiences a tensile stress resulting from the application of a 3600 N force? The elastic modulus for steel is 20 × 1010 Nm2/kg2. ΔL = m
The elastic portion of the stress-strain diagram for an aluminum alloy is shown in the figure below (Figure 1). The specimen from which it was obtained has an original diameter of 12.7 mm and a gage length of 50.5 mm. Take v=0.35 Figure σ (MPa) 490 0.007 € (mm/mm) Part A If a load of P = 40 kN is applied to the specimen, determine its new diameter. Express your answer to four significant figures and include appropriate units. d= Submit Part B L= O Value Submit μA Request Answer Determine its length. Express your answer to four significant figures and include appropriate units. Provide Feedback Value Units Request Answer ? Units ?
Help