Q2/ Consider a 1.2-m-high and 2-m-wide glass window whose thickness is 6 mmand thermal conductivity is k = 0.78 W/m. °C. Determine the steady rate of heattransfer through this glass window and the temperature of its inner surface for aday during which the room is maintained at 24°C while the temperature of theoutdoors is 5°C. Take the convection heat transfer coefficients on the inner andouter surfaces of the window to be h1 = 10 W/m2 °C and h2= 25 W/m2 °C, anddisregard any heat transfer by radiation.

In this problem, we will compute the constant rate of heat transfer which implies the temperature is…

/ Consider a 1.2-m-high and 2-m-wide glass window whose thickness is 6 mm thermal conductivity is k = 0.78 W/m °C. Determine the steady rate of heat sfer through this glass window and the temperature of its inner surface for a during which the room is maintained at 24°C while the temperature of the doors is 5°C. Take the convection heat transfer coefficients on the inner and . er surfaces of the window to be h1 = 10 W/m2 °C and h2 = 25 W/m2. °C, and regard any heat transfer by radiation. .

/ Consider a 1.2-m-high and 2-m-wide glass window whose thickness is 6 mm thermal conductivity is k = 0.78 W/m °C. Determine the steady rate of heat sfer through this glass window and the temperature of its inner surface for a during which the room is maintained at 24°C while the temperature of the doors is 5°C. Take the convection heat transfer coefficients on the inner and . er surfaces of the window to be h1 = 10 W/m2 °C and h2 = 25 W/m2. °C, and regard any heat transfer by radiation. .

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Heat transfer
A long 20 cm diameter shaft made of stainless steel 304 comes out of an oven at a uniform temperature of 600°C. The shaft is then allowed to cool slowly in an environment at 200°C with an average heat transfer coefficient of h = 80 W/m².K. Determine [a] the temperature at the center of the shaft and [b] the temperature of the outer surface of the shaft 45 minutes after the start of the cooling Given: Find: Schematic: Assume: Property Data: k= 14.9 W/m°C p= 7900 kg/m³ Cp = 477 J/kg:K a= 3.95 x 10-6 m²/s
A cold storage compartment is 6.95m long by 5.9m wide by 4.9m high. The four walls, ceiling and floor are covered to a thickness of 133.6mm with insulating material which has a coefficient of thermal conductivity of 5.8x10-2 W/m-K. Calculate the quantity of heat leasing through the insulating per hour when the outside and inside face temperature of the materials is 15°C and -5°C respectively. Ans. 6499.681 kJ/hr
Two rods ( fins) having same dimensions , one made of brass ( k = 85 Wm K) and the other of copper ( k = 375 W/m K ) , having one of their ends inserted into a furnace . At a section 10.5 cm a way from the furnace , the temperature of brass rod 120oC . Find the distance at which the same temperature would be reached in the copper rod ? both ends are exposed to the same environment .
Consider a 10m deep wall with a cross section as shown below. If the temperature on the left side of the wall is 100oC and the temperature on the right side is 30oC, determine: Total thermal resistance of the wall Heat transfer rate through the wall (as a vector) The convective heat transfer coefficient (h) of the air on the left side of the wall if ambient temperature is 120oC
Q) An apple has been put into a freezer at (-13°C) to be cooled. Initially, the apple is at a uniform temperature of 23°C. The convection heat transfer coefficient on its surface is 7 W/m2.°C. Assuming the apple as a sphere having a diameter of 6.5-cm and taking its properties as p = 930 kg/m³, cp = 3010 J/kg°C, and k 0.490 W/m-°C, determine; (a) the center = %3D temperature of the apple in 30 minutes, (b) the actual amount of heat transfer from the apple, and (c) the final equilibrium temperature of the apple. Hint: consider the temperature is a function of location and time.
consider a large plane wall of thickness 0.21 m, thermal conductivity k=1.2 w/m-c and surface area of 15 m. the two side of the wall maintained at constant temperature of 121 c and 52 c respectively. determine the rate of heatconduction through the wall under steady condition
Calculate the heat transfer rate from a single-pane glass window with aninside surface temperature of approximately 20° C and an outside surfacetemperature of 5° C . The glass is 1 m tall, 1.8 m wide, and 8 mm thick, asshown . The thermal conductivity of the glass is approximatelyk = 1.4 W⁄m ·K .
a 1 m-wide by 2 m-high window is composed of two 5 mm-thick glass panes, seperated by an air space of 10 mm. the temperature at the inner and outer surfaces of the window are 15 C and -20 C respectively. If the thermal conductivities of the glass pane and the air space are 1.4 w/m-k and 0.024 w/m-k, respectively. find the total conduction thermal resistance of the window in k/w
A flat wall is exposed to an environmental temperature of 38oC. The wall iscovered with a layer of insulation 2.5 cm thick with a thermal conductivity of 1.4W/moC, and a temperature of the inside wall is 315oC. The wall loses heat to theenvironment by convection. Compute the value of the convective heat transfercoefficient that must be maintained on the outer surface of the insulation to ensurethat the outer surface temperature does not exceed 41oC
Electrically heated draw batch furnaces are commonly used in the heat treatment industry. Consider a draw batch furnace front made of a 20-mm thick steel plate with a ther- mal conductivity of 25 W/m-K. The furnace is situated in a room with surrounding air temperature of 20 C and an aver- age convection heat transfer coefficient of 10 W/m2-K. If the inside surface of the furnace front is subjected to uniform heat flux of 5 kW/m2 and the outer surface has an emissiv- ity of 0.30, determine the inside surface temperature of the furnace front. I= 20°C Furnace front 4=5kW/m Air, 20 C h= 10 W/m K E=0,30 A= 25 Wim K Page 4.
Location of maximum temperature within the plate from its left face