Concept Simulation 9.1 illustrates how the forces can vary in problems of this type. A hiker, who weighs 785 N, is strolling through the woods and crosses a small horizontal bridge. The bridge is uniform, weighs 3110 N, and rests on two concrete supports, one on each end. He stops 1/5 of the way along the bridge. What is the magnitude of the force that a concrete support exerts on the bridge (a) at the near end and (b) at the far end? (a) Number i (b) Number i Units Units ✰

Concept Simulation 9.1 illustrates how the forces can vary in problems of this type. A hiker, who weighs 785 N, is strolling through the woods and crosses a small horizontal bridge. The bridge is uniform, weighs 3110 N, and rests on two concrete supports, one on each end. He stops 1/5 of the way along the bridge. What is the magnitude of the force that a concrete support exerts on the bridge (a) at the near end and (b) at the far end? (a) Number i (b) Number i Units Units ✰

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Similar questions

A 2.4 m ladder rests on a vertical wall as shown in the figure. The ladder has 7 rungs and the rungs are spaced 0.30 m apart, and the top and bottom rungs are 0.30 m from their respective ends of the ladder. Surfaces at A and B both have the same coefficient of friction. If a worker weighs 360 N and stands on the middle rung, determine the minimum value of the coefficient of friction so that the ladder does not slide. Neglect the weight of the ladder.
A bridge crossing a ravine has mass Mb and length L. The bridge is supported by pilings at points A and B at the right and left ends. A truck of mass mt stops at the point L/3 from point B. Find expressions for Fa and Fb, the forces supporting the bridge at each end.
Problem: A 80 kg construction worker is sitting 2.0 m from the right end of a 1450 kg, 6.0 m long beam. What is the tension in the cable attached at an angle of 30 deg. from the beam? (A) Pictorial Representation (B) Physical Representation
A 2.0-m-long rod has a density in kilograms per meter A = a + bx ,where a = 1.0 kg/m, b = 1.0 k9/m², and x is the distance from the left end of the rod. The rod rests horizontally with each end supported by a scale. The force exerted by the left scales is 39.2 N 22.9 N 16.3 N 4.0 N 32.6 N
Q4.2. A springboard-type diving board is built from high grade aluminum. This particular board has a mass of 65 kg and is 3.85 m long. 33.8 cm wide, and 5 cm thick. (Aside: Most springboards start thick on one end, then get thinner as it moves to the other end. For this problem, assume the springboard has a constant thickness) One end of the springboard is attached to a hinge. The hinge lets the springboard move up and down, but keeps it from sliding out of place. 1.1 m away from the hinge, the springboard rests on (but is not attached to) a fulcrum. A diver with a mass of 65 kg stands on the far end of the springboard (opposite from the hinge), ready to begin their dive. Hinge Fulcrum Note: the measurements for this problem were taken from the springboards used in the 2016 Summer Olympics, 3 m Springboard event.
When a person stands on tiptoe (a strenuous position), the position of the foot is as shown in Figure a. The total gravitational force on the body, F, is supported by the force n exerted by the floor on the toes of one foot. A mechanical model of the situation is shown in Figure b, where T is the force exerted by the Achilles tendon on the foot and R is the force exerted by the tibia on the foot. Find the values of T, R, and e when F, = n = 675 N. (For e, enter the smaller of the two possible values between 0° and 90°.) Achilles tendon Tibia 15.0° 18.0 cm 25.0 cm T = N R = N Need Help? Read It
The system shown in the figure is in equilibrium. If the block has a mass of 7 kg and the angle θ = 32. What is the tension in the string connecting the block to the wall? Express your answer in Newtons.
A vaulter is holding a horizontal 3.00-kg pole, 4.50 m long. His front arm lifts straight up on the pole, 0.750 m from the end, and his back arm pushes straight down on the end of the pole. How much force does his front arm exert on the pole? [?]N
The truss structure in a Figure Q4a is supported at A and B and has three forces acting vertically at nodes D, E and C, where F₁ = 25 KN, F2 = 75 kN and F3 = 35 kN. The horizontal distance between nodes A and B is d₁= 3.50 m and the horizontal distance between nodes B and C is d₂= 3.50 m. The angle a = = 60°, B = 60° and angle 0 = 30°. α F1₁ d1 3 IB * F2 E d2 Ꮎ F3 с Figure Q4a a) Determine the reactions at RA and Rc and A and C. Give your answers in kilonewtons (kN) to two decimal places. b) Determine the force acting in member AB and clearly state if the member is in compression or tension. Give your answer in kilonewtons (kN) to two decimal places.
pls write clearly
Please help me by showing step by step.
A hungry bear weighing 725 N walks out on a beam in an attempt to retrieve a basket of goodies hanging at the end of the beam (see the figure below). The beam is uniform, weighs 200 N, and is 6.50 m long, and it is supported by a wire at an angle of = 60.0°. The basket weighs 80.0 N. x+ Goodies (a) Draw a force diagram for the beam. (Submit a file with maximum size of 1 MB.) Choose File No file chosen This answer has not been graded yet. (b) When the bear is at x = 1.18 m, find the tension in the wire supporting the beam. N When the bear is at x = 1.18 m, find the components of the force exerted by the wall on the left end of the beam. (Assume the positive +x direction is to the right and the positive +y direction is upward. Include the sign of the value in your answer.) Fx = Fy N N (c) If the wire can withstand a maximum tension of 850 N, what is the maximum distance the bear can walk before the wire breaks? m