A fence post of mass m = 8 kg supports a fence with three lengths of barbed wire. The bottom wire is a distance d = 0.35 m from the ground and each wire is a distance 0.35 m above the previous one. Each of these three wires has the tension on it. For this problem, assume that the force exerted by these wires is purely horizontal. An additional guy wire is used to keep the pole upright with a tension of Fa = 490 N. The guy wire attaches to the post at a point h = 0.86 m above the ground and makes an angle of θ = 45 with respect to the horizontal. Write an expression for the tension in any one of the three fence wires. What is the normal force that the ground exerts upward on the post?

A fence post of mass m = 8 kg supports a fence with three lengths of barbed wire. The bottom wire is a distance d = 0.35 m from the ground and each wire is a distance 0.35 m above the previous one. Each of these three wires has the tension on it. For this problem, assume that the force exerted by these wires is purely horizontal. An additional guy wire is used to keep the pole upright with a tension of Fa = 490 N. The guy wire attaches to the post at a point h = 0.86 m above the ground and makes an angle of θ = 45 with respect to the horizontal. Write an expression for the tension in any one of the three fence wires. What is the normal force that the ground exerts upward on the post?

Similar questions

1. The figure shows a horizontal steel beam with mass M = 500 kg and length L = 2.0 m held against a vertical wall by a taut cable with 0 = 60°. A ball with mass m = 200 kg is attached via a short cable at a distance x 1.5 m from the wall. = a. Draw an extended force diagram for the steel beam, drawing the direction of the forces and the location of the forces acting on the beam. Ꮎ X m b. Using the contact point between the wall and the beam as your pivot point for torque calculations, balance the torques created by all the forces acting on the beam to determine the magnitude of the tension force that the cable exerts on the beam. C. Balance the forces in the x- and y-directions to determine the x- and y-components of the force that the wall exerts on the beam.
A wrecking ball (weight = 5670 N) is supported by a boom, which may be assumed to be uniform and has a weight of 2760 N. As the drawing shows, a support cable runs from the top of the boom to the tractor. The angle between the support cable and the horizontal is 32°, and the angle between the boom and the horizontal is 48°. Find (a) the tension in the support cable and (b) the magnitude of the force exerted on the lower end of the boom by the hinge at point P. (a) Number (b) Number Mk Support, cable Units Units N N 48 Boom
A 14.0 m uniform ladder weighing 480 N rests against a frictionless wall. The ladder makes a 55.0°-angle with the horizontal. (a) Find the horizontal and vertical forces (in N) the ground exerts on the base of the ladder when an 850-N firefighter has climbed 4.10 m along the ladder from the bottom. horizontal force magnitude 342.35 direction vertical force magnitude direction towards the wall up m N ✪ N (b) If the ladder is just on the verge of slipping when the firefighter is 9.10 m from the bottom, what is the coefficient of static friction between ladder and ground? (c) What If? If oil is spilled on the ground, causing the coefficient of static friction to drop to half the value found in part (b), what is the maximum distance (in m) the firefighter can climb along the ladder from the bottom before the ladder slips?
A bridge crossing a ravine has mass Mb and length L. The bridge is supported by pilings at points A and B at the right and left ends. A truck of mass mt stops at the point L/3 from point B. Find expressions for Fa and Fb, the forces supporting the bridge at each end.
A beam of length 11 m is supported as shown below. There is a pin in the bottom end of the beam and a mass hanging from the top end of the beam. If the mass of the beam is mb =264 kg, the hanging block has a mass of m1 =81.8 kg, theta = 50.1 degrees, and phi = 35.1 degrees, what is magnitude of the tension in the wire attaching the beam to the ground?
How do you do this? A hungry bear weighing 700 N walks out on a beam in an attempt to retrieve a basket of goodies hanging at the end of the beam (see figure below). The beam is uniform, weighs 200 N, and is 6.00 m long, and it is supported by a wire at an angle of ? = 60.0°. The basket weighs 80.0 N. a) When the bear is at x = 1.00 m, find the tension (in N) in the wire supporting the beam and the components of the force exerted by the wall on the left end of the beam. b) If the wire can withstand a maximum tension of 875 N, what is the maximum distance (in m) the bear can walk before the wire breaks?
A 2.0-m-long rod has a density in kilograms per meter A = a + bx ,where a = 1.0 kg/m, b = 1.0 k9/m², and x is the distance from the left end of the rod. The rod rests horizontally with each end supported by a scale. The force exerted by the left scales is 39.2 N 22.9 N 16.3 N 4.0 N 32.6 N
A meter stick with a mass of 0.83 kg is held perpendicular to a vertical wall by a cord of length d = 1.8 m attached to the end of the meter stick and also to the wall above the other end of the meter stick. (a) Determine the tension in the cord. N(b) Will the tension in the cord will be greater than, less than, or the same as that found in part (a) if the string is shortened? greater thanless than the same as
When a person stands on tiptoe (a strenuous position), the position of the foot is as shown in Figure a. The total gravitational force on the body, F, is supported by the force n exerted by the floor on the toes of one foot. A mechanical model of the situation is shown in Figure b, where T is the force exerted by the Achilles tendon on the foot and R is the force exerted by the tibia on the foot. Find the values of T, R, and e when F, = n = 675 N. (For e, enter the smaller of the two possible values between 0° and 90°.) Achilles tendon Tibia 15.0° 18.0 cm 25.0 cm T = N R = N Need Help? Read It
A hungry bear weighing 735 N walks out on a beam in an attempt to retrieve a basket of goodies hanging at the end of the beam (see the figure below). The beam is uniform, weighs 200 N, and is 5.50 m long, and it is supported by a wire at an angle of e = 60.0°. The basket weighs 80.0 N. Goodies (a) Draw a force diagram for the beam. (Submit a file with a maximum size of 1 MB.) Choose File No file chosen This answer has not been graded yet. (b) When the bear is at x = 1.20 m, find the tension in the wire supporting the beam. When the bear is at x = 1.20 m, find the components of the force exerted by the wall on the left end of the beam. (Assume the positive +x direction is to the right and the positive +y direction is upward. Include the sign of the value in your answer.) F = (c) If the wire can withstand a maximum tension of 875 N, what is the maximum distance the bear can walk before the wire breaks?
When a person stands on tiptoe (a strenuous position), the position of the foot is as shown in Figure a. The total is supported by the force n exerted by the floor on the toes of one foot. A mechanical gravitational force on the body, F model of the situation is shown in Figure b, where T is the force exerted by the Achilles tendon on the foot and R is the force exerted by the tibia on the foot. Find the values of T, R, and 0 when F, = n = 770 N. (For 0, enter the smaller of the g' two possible values between 0° and 90°.) -Achilles tendon Tibia 15.0° 18.0 cm 25.0 cm a T = R = N = Submit Answer
The truss structure in a Figure Q4a is supported at A and B and has three forces acting vertically at nodes D, E and C, where F₁ = 25 KN, F2 = 75 kN and F3 = 35 kN. The horizontal distance between nodes A and B is d₁= 3.50 m and the horizontal distance between nodes B and C is d₂= 3.50 m. The angle a = = 60°, B = 60° and angle 0 = 30°. α F1₁ d1 3 IB * F2 E d2 Ꮎ F3 с Figure Q4a a) Determine the reactions at RA and Rc and A and C. Give your answers in kilonewtons (kN) to two decimal places. b) Determine the force acting in member AB and clearly state if the member is in compression or tension. Give your answer in kilonewtons (kN) to two decimal places.