concentration of the total suspended solid. In the laboratory, 5 mL of the water sample was ransferred to a 100 mL volumetric flask before diluted with distilled water to 100 mL. After that, 50 mL of the diluted water sample was transferred to a funnel containing a glass fiber filter and attached to a glass flask with the sidearm connected to a operating vacuum pump. Transferred diluted water sample was left drained through the glass filter before glass fiber was transferred to an oven to heat at 105 oC under a constant weight of 0.2654 g was obtained. If the initial weight of the glass fiber filter is 0.2431 g. Calculate the amount of the suspended solid in mg unit contained

concentration of the total suspended solid. In the laboratory, 5 mL of the water sample was ransferred to a 100 mL volumetric flask before diluted with distilled water to 100 mL. After that, 50 mL of the diluted water sample was transferred to a funnel containing a glass fiber filter and attached to a glass flask with the sidearm connected to a operating vacuum pump. Transferred diluted water sample was left drained through the glass filter before glass fiber was transferred to an oven to heat at 105 oC under a constant weight of 0.2654 g was obtained. If the initial weight of the glass fiber filter is 0.2431 g. Calculate the amount of the suspended solid in mg unit contained

Chemistry

10th Edition

ISBN:9781305957404

Author:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Publisher:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Chapter1: Chemical Foundations

Section: Chapter Questions

Problem 1RQ: Define and explain the differences between the following terms. a. law and theory b. theory and...

See similar textbooks

Similar questions

A 25mL volumetric pipet is used to deliver a sample of the stock solution marked “0.6000M X2SO4” into a 100mL volumetric flask. Distilled water is added to the flask until it is about 3/4thfull, the solution is mixed well, then more water is added to fill it up to the calibration mark, then it is mixed again. Calculate the concentration of X+ion in the dilute solution made above.
A student was given a stock aluminum(III) solution with a concentration of 5.000 parts per million (ppm). (ppm are defined as mg/L for dilute aqueous solutions.) The student prepared five 100 mL standard solutions and an unknown as described in the procedure section of the experiment. The absorbance of each solution was read at 565 nm, using the blank to set zero absorbance. The results are tabulated below. Solution Volume of Al(III) stock solution used (mL) Absorbance 1 8.00 0.701 2 6.00 0.548 3 4.00 0.378 4 2.00 0.208 5 1.00 0.123 Unknown --- 0.534 3. What is your best estimate of the Al(III) concentration of the unknown sample in the cuvet based upon where its absorbance falls on the standard curve?
5.0 mL of 1-butanol was mixed with 10 mL of HCl. The reaction was put on an ice bath and 4 mL of concentrated sulfuric acid was added. This mixture was refluxed for 45 min and then the product was co-distilled with water using a simple distillation apparatus. Water and the product are immiscible. 1-butanol has a molar mass of 74.12 g/mol, a density of 0.810 g/mL, and a boiling point of 118 C. The product has a molar mass of 92.57 g/mol, a density of 0.880 g/mL, and a boiling point of 78 C. What is the nucleophile in this reaction? What is the role of H2SO4 in this reaction? Calculate the theoretical yield for this reaction. Give your answer in grams. Select the following statements that can be said about the reaction shown.
The protein concentration of a protein isolate was determined using the Bradford assay. Five dilution of bovine serum albumin (BSA) were prepared from a 5.00 mg/mL BSA stock solution. To these dilutions, 100 µl of Bradford reagent were added. After 5 minutes, the absorbance was taken at 595 nm. Standard # BSA, in mg/mL Volume of Bradford reagent, A595 in mL 1 5.0 0.000 1.00 5.0 0.134 3 2.00 5.0 0.265 4 3.00 5.0 0.388 4.00 5.0 0.497 The supernatant dilution was prepared by mixing 49 µL of the protein isolate with 16 µL water. The absorbance was taken 5 minutes after addition of 100 mL Bradford reagent. Calculate the protein concentration (in mg/mL) of the original isolate if the absorbance at 595 nm was 0.413. Note: Final answer format must be x.xxx (three decimal places). Round off only in the final answer. Do not round off in the middle of calculation.
A 100 ml bottle of metronidazole 100 mg/ml suspension is available in your pharmacy. Calculate the volume of this suspension needed to be diluted with cherry syrup to prepare 60 ml of a 4% metronidazole suspension. 1 ml of a 1:1000 epinephrine injection was mixed with 20 ml of 1% lidocaine injection. Calculate the new ratio strength of epinephrine in the admixture. (IGNORE ANY VOLUME CHANGES AFTER ADMIXTURE) Instead of preparing 4 grams of tetracaine hydrochloride 4% gel an 8% gel was compounded by mistake. How many grams of the 8% gel and gel base must be mixed to get 4 grams of a 4% gel? How many milliliters of 70% ethanol and 20% ethanol must be mixed to prepare 500 ml of 30% ethanol? A diphenhydramine elixir contains 12.5 mg drug in one teaspoon. The volume of oral vehicle that is to be added to 100 ml of this elixir to reduce its strength by one half its original strength is; 6. 90 capsules of Liothyronine (T3) 15 micrograms are to be prepared. The formula calls for a 1:10000…
A student determined fluoride in a toothpaste sample using ion chromatography. A toothpaste sample of mass 0.100 g was dissolved in type I water and then quantitatively filtered through a Whatman #1 filter paper into a clean 100 ml volumetric flask. The flask was then made up to volume with type I water and mixed thoroughly.A portion of the solution was filtered through a 0.45 um filter into a sample vial for analysis. Analysis of the sample gave a fluoride concentration of 1.60 mg/l Calculate the % w/w fluoride in the original toothpaste sample. (Give your answer to 3 decimal places please)
Solution 1 Solution 2 Solution 3 Solution 4 Solution 5 Concentration iron(III) nitrate 0.00200 0.00200 0.00200 0.00200 0.00200 [Fe(NO3)3] (M) Concentration potassium thiocyanate 0.00200 0.00200 0.00200 0.00200 0.00200 [KSCN] (M) Volume Fe(NO3)3 (mL) 5.00 5.00 5.00 5.00 5.00 Volume KSCN (mL) 5.00 4.00 3.00 2.00 1.00 Volume DI water (mL) 0.00 1.00 2.00 3.00 4.00 Initial concentration [Fe3+] (M) 0.00100 0.00100 0.00100 0.00100 0.00100 Initial concentration [SCN‍] (M) 0.00100 0.000800 0.000600 0.000400 0.000200 Absorbance 0.269 0.192 0.154 0.104 0.052 Equilibrium [FeSCN2+] (M) 0.000198 0.000141 0.000113 0.0000765 0.000038 Equilibrium constant Kc Average Kc
escriptionSolubility (soluble, insoluble, miscible & immiscible)25 mL of water and 1 g of salt—the resulting mixture is clear and colorless 25 mL of water and 1 g of solid silver chloride—the resulting mixture is cloudy and solid settles out. 25 mL of water and 5 mL of mineral oil—the resulting mixture is cloudy and gradually separates into two layers.
Oral rehydration salts are stated to contain the following components: Sodium Chloride 3.5g Potassium Chloride 1.5g Sodium Citrate 2.9g Anhydrous Glucose 20.0g 8.342 g of oral rehydration salts are dissolved in 500 ml of water. 5 ml of the solution is diluted to 100 ml and then 5 ml is taken from the diluted sample and is diluted to 100 ml. The sodium content of the sample is then determined by flame photometry. The sodium salts used to prepare the mixture were: Trisodium citrate hydrate (C6H5Na3O7, 2H2O) MW 294.1 and sodium chloride (NaCl) NW 58.5. Atomic weight of Na = 23. The content of Na in the diluted sample was determined to be 0.3210 mg/100 ml. Determine the % of stated content of Na in the sample. The stated should be 104.5, how??
A pipet is used to transfer 5.00 mL of a 1.25 M stock solution in flask “S” to a 25.00-mL volumetric flask “B,” which is then diluted with DI H2O to the calibration mark. The solution is thoroughly mixed. Next, 3.00 mL of the solution in volumetric flask “A” is transferred by pipet to a 50.00-mL volumetric flask “B” and then diluted with DI H2O to the calibration mark. Calculate the molarity of the solution in volumetric flask “B.”
Effect of Particle Size on the Rate of Dissolving Time required for all NaCl to dissolve Sample Results after 2 minutes shaking Do you think the size of the crystal makes a difference in how fast the salt dissolves? Explain why the differences you observed and why they happened. Effect of Temperature on the Rate of Dissolving Time required for all NaCl to dissolve Sample Observations Do you think the temperature of the water makes a difference in the rate at which the NaCl dissolves? Explain why the differences you observed and why they happened. Page 3 of 6
5 mL of HCl and 5 mL of CH3COOH solutions are titrated with a pipette in a glass bottle and 150 mL of distilled water is added. The initial conductivity (720) of this diluted mixture is measured and recorded in the table. Then, one ml of M/10 NaOH solution is added and their conductivity is measured and recorded in the table. Find the concentration of HCl and CH3COOH.