Compute the total vertical stress o, pore water pressure u, and then the effective vertical stress o at Points A, B, C, and D in the soil profile shown in the following figure. Plot those with the depth z. Soil 1, y; = 18.0 kN/m³ A.. -6 Yt = 18.4 kN/m³ B -10

Q: 90 MPa 60 MPa 20 MPa

A: Given, Normal stress in x-direction = σx = -20 MPa Normal stress in y-direction = σy = 90 MPa Shear…

Q: Problem 9 Problem 8.2-11 A hollow pressurized sphere having radius r = 4.8 in. and wall thickness r-…

A: Given data,

Q: The beam shown below has a cross section of channel shape with width b-400 mm and height h=80 mm,…

A: Answer: (a) The maximum tensile stress is 64.68 MPa. (b) The maximum compressive stress is 16.36…

Q: If the horizontal displacements of nodes 2 and 3 of the following element are q2=0.1 mm and q3=-0.05…

A: Given displacement of node 2 and 3.  Required: Horizontal displacement of point P. (d)

Q: Hydraulics In Exercises 41-44, determine the location of the horizontal axis y, at which a vertical…

A:

Q: A hydraulic punch press is used to punch a slot in a 0.50-in.-thick plate, as illustrated in Figure.…

A:

Q: A circular plate with simply suppo KPa, as shown below, is considered. The plate thickness is h=23…

A: Pressure = P = 10 kPaPlate thickness  h = 23mmRadius of plate = 1.180 mmYoung's Modulus = 70 GPa =…

Q: The pressure drop needed to force water through a horizontal 1-in.-diameter pipe is 0.40 psi for…

A:

Q: 4 - A rectangular block is loaded with a 180 kN axial force and a moment M, as shown in the figure.…

A: Given data:-  Axial force =180 kN the maximum allowable tensile stress = 50 MPa To find:- the…

Q: You are asked to design a 180° reducing bend to attach to a pipe that conveys water at a water…

A: To calculate the smallest safe bolt diameter, we need to consider the stresses induced in the bolts…

Q: Find the moment M at O to hold the gate 45⁰ Gate 2 m wide Fig.1 M O Water 700 mm 350 mm 1.3 m…

A: Consider the U-tube manometer and write the head-balance and calculate the pressure at the top of…

Q: Find hydraulic radius A=6 m2 P=8 m

A: To find : The hydraulic radius of the construction. Given :  The cross section Area is A=6 m2. The…

Q: A cap plate at the bottom of the brace distributes the load P = 660 kN to four flange plates…

A:

Q: If the horizontal displacements of nodes 2 and 3 of the following element are q2=0.18 mm and…

A: Given displacement of nodes 2 and 3.  Required: horizontal displacement of point P (d)

Q: L 32 mm L Cross-section K, aran : 17 nam + 6 E= 200 kN/mm m = 15 kg KI= lo kN/m Find f

A:

Q: If maximum shear stress is 45 N/mm2 in rectangular section. Width =4 m depth=6 m Find maximum shear…

A: Given data : Width=b Depth=d Maximum shear stress=ζMax   Required : Maximum shear force

Q: Determine the maximum value of Q of the Transverse Shear Stress formula [T = (VQ)/(It)] in mmo for…

A: Given: To determine the maximum value of Q.

Q: Find the maximum shear stress in rectangular section if normal shear stress value is 22 Mpa

A: Given data : Normal shear stress =ζ ζ=22 MPa   Required : Maximum shear stress

Q: oss section of a beam is as shown in Figure Q1(a),determine; (i) center of gravity with respect to…

A:

Q: A water gate is to be reinforced with three horizontal beams (running to the page). If the water…

A: A water gate is to be reinforced with three horizontal beams (running to the page). If the water…

Q: A thin wall spherical tank of diameter 1.5 m and wall thickness 65 mm has internal pressure of 20…

A:

Q: 4. A 2-slug mass is dropped from an airplane with initial downward velocity zero. Find v(t) for t≥ 0…

A:

Q: X 35 kPa 40 kPa 95 kPa

A: As stated in question, Stress along x-direction = σx = -95 kPa Stress along y-direction = σy = -35…

Q: Required Information NOTE: This is a multi-part question. Once an answer is submitted, you will be…

A: The weight of each pipe is The length of pipe is The diameter of each pipe is .

Q: If the horizontal displacements of nodes 2 and 3 of the following element are q2=0.1 mm and q3=-0.05…

A: Given data: ξ1 = -1 & η1 = -1 ξ2 = 1 & η2 = -1 ξ3 = 1 & η3 = 1 ξ4 = -1 & η4 = 1 q2 =…

Q: A long retaining wall is braced by wood shores set at an angle of 308 and supported by concrete…

A: Given Data The length of the wall is: 3 m The resultant force acting on the wall is: 190 kN The…

Q: HINGE AT A GATE Z Et WIDE FIND FB Fe IS TO LIFT GATE NORMAL To AC

A:

Q: beam sectlon. Plot the normal stress distr:bution by The location center of gravity of the beam…

A: The schematic diagram of the given section is Part 1: - A rectangle whose sides are 38 mm and 150…

Q: Find the maximum shear stress in rectangular section if normal shear stress value is 22 Mpa

A:

Q: Find the value of Maximum shear stress in rectangular section Shear force-40 N Area of section=2 mm2

A: Given data : Shear force V=40 N Section=Rectangular  Area of section A=2 mm2

Q: Sind y at 2 m from the left hand 7111 سحله ولي dx

A: Concept: The integration of the load intensity is the shear force. The integration of the shear…

Q: Given data Maximum shear force=10 KN Rectangular section width=5 m Depth =10 m Determine maximum…

A: Given data : Rectangular section Width=B Depth=D Maximum shear force=V   To find : Maximum shear…

Q: as shown in figure below. Determine the maximum depth of water in the channel if the tensile and…

A: Givenσt=18MPaσc=48MPaγw=9.81 kN/m3γc=68 kN/m3

Q: The internal shear force at a certain section of a steel beam is V = 185 kN. The beam cross section…

A: To findthe shear stress at point A, which is located at  below the centroid of the wide-flange…

Q: The steel pipe of length L = 541 mm is filled with concrete and subjected to a compressive force P =…

A:

Fluid Dynamics

The study of the flow of gases and liquids, usually in and around solid surfaces, is known as fluid dynamics in physics and engineering. Fluid dynamics, for example, can be used to evaluate the movement of air through an airplane wing or the surface of a vehicle. It can also be used in ship design to increase the speed at which ships pass through water.