Compute the radius of relative stiffness of 15 cm thickcement concrete slab from the following data:2,10,000 kg/cmModulus of elasticity of cement concrete =Poisson's ratio for concrete 0 130 133.0 kg/cm3(ii) 7.5 kg/cm3Modulus of subgrade reaction, K =(1)

Given, Modulus of elasticity of cement concrete E = 210000kg/cm³ Poisson's ratio u = 0.13

Compute the radius of relative stiffness of 15 cm thick cement concrete slab from the following data : Modulus of elasticity of cement concrete = 2,10,000 kg/cm Poisson's ratio for concrete 0 13 2 3.0 kg/cm3 (ii) 7.5 kg/cm3 Modulus of subgrade reaction, K = (1)

Compute the radius of relative stiffness of 15 cm thick cement concrete slab from the following data : Modulus of elasticity of cement concrete = 2,10,000 kg/cm Poisson's ratio for concrete 0 13 2 3.0 kg/cm3 (ii) 7.5 kg/cm3 Modulus of subgrade reaction, K = (1)

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A concrete column with a circular hole is to be loaded in compression. a. What is the average compression stress in the column if the axial load is 14.5(10)6 N?b. Locate the application of the concentrated load (x,y) on the cross section of the beam. Note: Draw the Free Body Diagram, include the units/dimensions and round-off the answers to 3 decimal places.
Solid mechanics
Determine the plastic moment Mp of the cross section shown when the beam is bent about a horizontal axis. Assume the material to be elastoplastic with a yield strength of 169 MPa. 5 mm t=5 mm 120 mm 5 mm 80 mm The plastic moment is kN.m.
If a new type of material that's a hybrid of plastic and wood shavings is brittle and has an ultimate compressive strength of 20 MPa, an elastic modulus of 1000 MPa, and a Poisson's ratio of 0.20, A. Calculate the bulk modulus for plastic wood. B. Calculate the maximum strain that can be put on plastic wood. C. Assuming that plastic wood is isotropic, calculate the maximum hydrostatic pressure that can be put on plastic wood. D. If the plastic wood has a fracture toughness of 0.2 MPa-m.5, calculate the maximum crack length if the stress on the plastic wood is 1 MPa.
Please Solve the buoyant force and Specific Gravity of Buoyant. Show complete solution
Drow the shear and bending diagram
5/Determine the smallest value of uniform load that will cause a crack for the reinforced concrete beam shown below. Use f= 30 MPa Wer=? 3.6 m- Ø16mm 100 600 100-> 100 200 50
Q2) Layers of Brass, Steel and Aluminum are bonded together and formed section shown below. Cantilever beam is loaded at the tip with 100 kN. In the cross-section height of steel is 50 mm, height of the aluminum is 350 mm and height of the brass is 100 mm. Modulus of clasticity for the materials are given as; Steel, Est = 200 GPa, Aluminum, E = 70 GPa and Brass, Esr= 105 GPa. Find the maximum axial stresses under given loading for Steel, Aluminum and Brass, separately. Steel 150 kN 500 mm 50 mm Aluminum Aluminum 350 mm Brass Brass 100 mm Cross Section of the 5 m Beam Fixed Side view of the Beam Support
Strain profiles of a flexural reinforced concrete element section at yield and failure conditions are given in Figure 1. (a) Does this section satisfy the curvature ductility requirement of µ ≥ 8. (b) Briefly indicate two possible design modifications by which the ductility of a reinforced concrete section can be improved. Ey Yield &c = 0.002 Øy Eu = 0.004 pu Es = 10ɛy Failure Figure 1: Strain Profiles fy = 460 MPa Es = 200 GPa
Need answer for this please
The composite bar is subjected to a normal force P = 7500 lb as shown in the figure. The section of the composite bar is composed of two hollow tubes and a solid steel core. Determine the axial stress developed in each bar. Use Ecu = 18 x 106 psi, Est = 30 x 106 psi, and Ebr = 16 x 106 psi.
The composite bar shown in the figure is firmly attached to unyielding supports. An Axial force P = 52 kips is applied at 65°F. Compute the stress (ksi) in the Aluminum at 116 °F. Assume a = 6.5 x 10-6/° F for steel and 12.8 x 106/°F for aluminum Given: L1 = 15in; L2 = 11in Your final answer should contain two decimal places Steel A = 3 in² E = 29 x 106 psi Correct Answer: 3.92 L2 Aluminum A = 2 in² E = 10 x 106 psi L1