Compute the orthogonal component of F= 6i + 20j- 12k Ib in the direction of the vector A = 2i - 3 j+ 5k ft Match each item to a choice: ORTHOGONAL COMPONENT: Choices: : -12.75 lb : -17.52 lb : 15.63 lb : 32.56 lb : -31.5 lb : 48.5 ft

Q: Lazuli. A radially uniform pen with a cross sectional area of a regular ~octagon was placed on a…

A:

Q: In performing his favorite workout routine, Jason throws a ball with an initial velocity of 12.3 m/s…

A:

Q: 9-67. Determine the principal stress, the maximum in-plane shear stress, and average normal stress…

A: Given:σx=350 MPaσy=-200 MPaζxy=500 MPa

Q: O MPa and an axial stress of 325 MPa that act on an element imposes a bending stress of 250 MPa and…

A: Tangential stress is .Axial stress is .Bending stress is .Torsional stress is .

Q: Two boys riding in bicycles A and B respectively travels towards each other. When the distance…

A:

Q: net heat rejected to reservoir C by CE-2

A: Given data; Carnot engine (CE-1) works between       two temperature reserviors A and B;TA=900…

Q: resolve solution

A:

Q: If the speed of the crate at A is 15 ft/s, which is increasing at a rate v = 3 ft/s², determine the…

A:

Q: Find the following. Show complete solution.

A: The given diagram is here, Section 1:- A rectangle OABC, whose sides are 120 mm and 80 mm Section…

Q: Boink! A pendulum of mass M₁ = 3.50 [kg] is released from rest at a height of # 0.500 [m] from the…

A:

Q: cked tables is a sh on the stack he tables are lo

A: GIVEN:

Q: 2. A vertical square surface as shown in the figure as shown in the figure has its upper edge…

A:

Q: If 1 ton of bituminous coal is burned to generate electricity, how many kWh could be produced if the…

A: Dear student,                     There are two different problems that you have posted but…

Q: A rectangular beam is 12 meters long. It is supported by R1 at the left end and R2, 4 meters from…

A: Solution is given below:

Q: A vacuum gauge mounted on a condenser reads 0.56 m Hg. What is the absolute pressure in the…

A:

Q: CS South-line. Consider a sphere with radius R and mass M. Assuming that the moment of inertia of…

A:

Q: The velocity of the hanging block of the system shown in Figure 1 is y = 0.05cos20t downward. a.…

A:

Q: air-standard Compression Ignition cycle has a compression ratio of 18.2. Air is at 3200°R at the of…

A:

Q: Conversion of units: A pyramid has a height of 500 ft, and its base covers an area of 15.0 acres…

A:

Q: haldog A -massless-spaghetti is wrapped around a solid cylindrical hakdog with mass M and radius R.…

A: To find: Tension in the hakdog, T = ?

Q: A vacuum gauge mounted on a condenser reads 66 cm Hg. What is the absolute pressure in the condenser…

A:

Q: SAMPLE PROBLEM 2: Assume that AE are equal for each rod Reqd: Internal forces for member AB, CD, EF…

A: Given Data: Length of the beam, L=0.8 m

Q: A 10 ft long steel member with pinned ends (i.e., pinned-pinned) is used as a column. The member…

A: From question, Length of steel shaft, L = 10ft=10×12 inch= 120 inch Thickness of member…

Q: B Problem 1 Piston A has a cross-section 1200cm while that of piston B is 950cm with the latter…

A:

Q: 3 The velocity of a particle which moves along the x axis is given by v = 2 – 4t + 5 tz, where t is…

A:

Q: An A-3 polyamde conveyor belt is to be.dnuen 530mm: Ihe pully shoift which is ya pulley with a…

A:

Q: The transmission tower is subjected to lateral forces as shown in the figure. Find the resultant…

A: given; F1=3KNF2=5KNF3=7KNa=2.55mb=1.8mc=1.8md=1.5mlets take vertical force at A=RAvlets take…

Q: What is the difference in potential energy per pound of mass of fluid at A and at B. STORAGE TANK…

A:

Q: A vehicle and trailer combination cross a 12-meter bridge with axle loads of 10, 20, and 30 kN…

A:

Q: 4/29 Determine the force in member CG. Ans. CG 14.14 kips T H 10 G 10 F 10 E 10 A B D 5 kips 5 kips…

A: Force in Member CG is 14.14 kips [Tension].

Q: Determine the Interplanar spacing and the length of the Burgers vector for slip on the preferred…

A:

Q: A certain vector in the xy plane has an x component of 4m and ay component of 10m. It is then…

A:

Q: A piston-cylinder device contains (0.85 kg) of refrigerant (134a) at (-10°C). The piston that is…

A: solution: mp = 12 kg mr = 0.85 kg P= 88 kPa T1= -10 C  T2 = 15 C

Q: Fill in the blanks: Compute the difference in pressure (Pa-PR) if pipe A contains oil with sg = 0.92…

A: To find PA-PB Specific gravity of oil =0.92 density of mercury = 13.6*10^3

Q: rmine the angular acceleration of each of the disks in Figure 2.

A:

Q: 4/4 Calculate the forces in members BE and BD of the loaded truss. B

A: To calculate the forces in the member BE and BD.

Q: The Reversed Carnot Cycle is used to run a food production company's refrigeration system. The…

A: As per bartleby guidelines we are allowed to solve 3 subparts if multiple subparts are posted.  So…

Q: A beam is subjected to equal 19.8 kip-ft bending moments. Assume t-t2-t2 in, d-13 in, b1-4 in, and…

A:

Q: designer of a ski resort

A: detailed Answer given below

Q: Question: For the figure shown below: 1- Locate the centroid C (x.y) of the shaded area 2- Determine…

A: Moment of inertia of an area is defined as the product of area and the distances of its center from…

Q: A rec tangular piece of wood, 50 mm by 100 mm section is urad in cross Compression block shown. De…

A: Answer: The axial force P that can be applied safely is 52.015 kN.

Q: A centrifuge bowl is to separate two immiscible liquids, one with SG 1.1 and the other with SG 0.9.…

A:

Q: 45. A power unit (pump and electric motor) has a power rating of 25 hp and supplies flow at a rate…

A: