Compute the net area of each tension member. Note that for a standard-size bolt hole, hole dia = bolt dia (in mm) + 3mm or hole dia. = bolt dia (in inches) + 1/8in. 1. PL 25 x 300 mm 25 mm Ø bolts 2. 19 mmØ bolts W12 x 40 - 3. An L8 x 4 x % with two lines of %-in dia. bolts in the long leg and one line of %- in dia. bolts in the short leg.

Compute the net area of each tension member. Note that for a standard-size bolt hole, hole dia = bolt dia (in mm) + 3mm or hole dia. = bolt dia (in inches) + 1/8in. 1. PL 25 x 300 mm 25 mm Ø bolts 2. 19 mmØ bolts W12 x 40 - 3. An L8 x 4 x % with two lines of %-in dia. bolts in the long leg and one line of %- in dia. bolts in the short leg.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Determine the smallest net area of the tension member shown in the figure. The holes are for 3/4-in Ø bolts at the usual gage locations. The stagger is 1 1/2 in. (Ans. 2.98 in^2)
Please answer all the questions with a complete solution. thank you.
For the cross section shown, calculate the tensile capacity of the steel plate. Assume that the bolt hole is 1/16 inch larger than bolt diameter. Plate 1/2" x 11" .T 7/8" dia. bolt, typ. ASTM A325N
The T-shape shown in the figure is used as a tension member. Given that the gross area Ag = 2556 mm², tw = 10 mm, gross depth d = 220 mm and bolts are 16-mm-diameter, with Fy=345 MPa and Fu = 450 MPa, calculate the nominal block shear strength for combined tensile rupture and shear rupture. Write your answer to the nearest whole number in kN. Consider Ubs = 1.0 T 40 mm. +* 125 mm O 4@.75 mm O O O O
SITUATION I A lapped bolted lension member is shown. Diameter of bolts are 22 mm and the plate material is A36 steel Fy = 275 MPа, Fи 3 415 МPа. Assume the fasteners are adequate and do not control the tensile capacity. Diameter of hole is 2.5 mm bigger than the diameter of bolt. 12 :: 350 50 100 100 50 50 1. Determine the tensile capacity of the lapped joint based on gross area. a. 252.656 kN c. 866.250 kN b. 202.125 kN d. 693.000 kN 2. Determine the net Area for the tensile capacity of the lapped joint. а. 3318 тm? c. 5250 mm? b. 1554 mm? d. 1824 mm? 3. Determine the tensile capacity of the lapped joint based on the net area. a. 752.856 kN C. 866.250 kN b. 688.845 kN d. 1039.500 kN
PL 5/8 x 12 3/4-in-diameter bolts
Please show solutions on how to get the 0.250 value. The circle green in the figure. Civil engineering- steel design
Please answer with complete details. Thank you. A = 1 B = 1 C = 2
Tension Member -Problem 2 9 - 4" Bolts Gusset Plate Plate thickness t = ½" 2" Tension Member A36 Steel Plate 3" P, 10" и 3" d h Compare Tension Capacity of line 2" e abcde and line An Ag fgchi 4" 4"
A double-angle shape is shown in the figure. The steel is A36, and the holes are for 1/2-inch-diameter bolts. Assume the Ae = 0.75An. Section 2L5 x 3 x16 LLBB Determine the allowable tensile strength for ASD. Select one: а. 52.1 b. 104.2 c. 87.8 d. 43.9