Compute the moments of inertia with respect to the X-X and Y-Y centroidal axes for the following areas. Make sure to draw the reference axes used in the calculations. Use tabulation method 1. 45 mm (typ.) 80 mm 80 mm

Q: for it because many people confuse it with something else so this time I am attaching a picture of a…

A: Required Torque Given data Key dimension are given Shaft diameter is given Allowing stress is also…

Q: What is a microcontroller? 1. General purpose device that can be programmed to carry out a finite…

A: Given question is related to electromechanical devices and controllers.

Q: While taking a break from the Extreme Beer Fest in Boston, you decide to do something educational…

A: Draw the diagram for the given movements for a better understanding of the question and final…

Q: Hi, I need help with the first part of the problem below because I'm very confused about how P1 and…

A: Approach to solving the question: Detailed explanation:Examples: Key references:

Q: Compute the moments of inertia with respect to the X-X and Y-Y centroidal axes for the following…

A:

Q: I need answers to problems 7, 8, and 9.  NOTE: Please stop wasting my time and yours by rejecting my…

A: The part name specified in the drawing is “BONNET SLEEVE”.

Q: Procedure: 1. Look up the materials that make up a smartphone. Take notes in a table like the one…

A: Minerals are the substance found in the earth's crust useful to mankind. Smartphone is a Pinnacle of…

Q: I need question 7 answered pertaining to the print provided. I asked this question previously on…

A: 7. According to ASME, the revision can be made either by making the changes in the revision block or…

Q: I need help answering questions 1,2, and 3 pertaining to the print attatched below.

A: 1stIn the given drawing there are 4 surface texture symbols.

Q: 1) 20N/m 60 N/m 4 m 2 m 2)

A:

Q: If it is INCOMPLETE SOLUTION and there are SHORTCUTS OF SOLUTION, I will rate you with…

A: Given Data⇒ Load intensity for rectangular section : F=4 KNm Distance upon which load is…

Q: I need help solving these 3 simple parts, if you can not answer all 3 parts then please leave it for…

A: Consider the first question:Detail drawing is a drawing that contains all the information…

Q: The question and data are in pictures. Please answer properly with each steps and explanation. Best…

A: To determine if Column 1 will remain stable if the water tank is placed directly above it, we need…

Q: Need help with this

A: We'll do the following actions to address the issue of finding the internal normal and shear forces…

Q: A 25 ft long solid steel rod is subjected to a load of 10,000 Ib. This load causes the rod to…

A: Data given -  L = 25 ft = 25 × 12 P = 10000 lb  ∆L = 0.477 in  E = 30 × 106  psi

Q: F 400 N E-600 N 45 30

A: Given: F1 = 600 N F2 = 400 N   To find: FR = ? and direction of resultant using parallelogram law of…

Q: I need answers to questions 13, 14, and 15 pertaining to the print provided. Note: A tutor keeps…

A: 13.Calculate the maximum material condition for the largest cylindrical part feature.

Q: a Show how Pip can complete the circuit by adding less than 120 cm of track. b Show how Pip can…

A:

Q: I need parts 3 and 4 answered pertaining to the print provided.  I asked this question previously on…

A: (3) In the empty space of revision A9 a general note 3.6 is added stated that the revised geometric…

Q: What is the equivalent resultant force and specify its location, measured from point 0. * FR= 13.5…

A:

Q: I need answers for problems 13, 14, and 15 pertaining to the print provided.   NOTE: If you refuse…

A: 13.A characteristic of a system which may cause failure or defects if not in line with quality…

Q: I need help solving problems 13, 14, and 15 pertaining to the print provided below.

A: 13.Dimensions of the same object should not be copied or we can say that the same information should…

Q: What is the unstretched length in DB? * O 1.572 m O 1.837 m O 1.769 m O 3.606 m

A:

Q: I need answers to questions 1, 2, and 3 pertaining to the print provided. Note: A tutor keeps…

A: Answer to question no. 1Yes, the print shows the detail drawing of a single part here. The drawing…

Q: how do i draw sectional view of this object.

A: A sectional view of an object is used to identify the parts interior construction of a part…

Q: I asked for problems 6 and 7 to be answered, but I did not get a properly structured answered as the…

A: Chamfer the edge at  45o  with 0.250” leg distance.

Moment of Inertia

Inertia can be termed as a resistance offered by a body to change its state. A rigid body initially at rest will apply resistance when acted by an external force that tends to change its state of rest or velocity, or a body initially at motion will provide resistance in changing its state of velocity or motion for coming to a state of rest. In other words, Newton's first law of motion describes the law of inertia of a rigid body.