Compute the mean annual precipitation for the river basin shown in the figure below using the Thiessen polygon method. The location of the various rain gauge stations and the point precipitation values are indicated in the table below. Fig.1. River basin and location of raingauges Table 3. Rainfall data and areas of thiesen polygon Rainfall, Pi (cm) Area (ha) 7.88 2.8 Raingauge Station A 84.0 B. 81.0 69.0 8.67 79.0 12.57 63.0 3.02 5.79 5.22 H. 58.0 61.0 69.0 8.45 K 56.0 8.05 Mean annual precipitation:

Q: 5. Find diameter y. All dimensions are in millimeters. 1 + 19.30 DIA 118.00 -३०

A: Tapered beam with larger diameter at AB = 19.3 mm  Length of beam ,L = 118 mm  Tapered angle = 3°…

Q: Draw the sectional front view (front section) and draw the orthographic projection (sideand top…

A: Asked: To draw the orthographic projection views of the given object.   The orthographic projection…

Q: Compute Ix for the region shown. y 2 18 2-5--5- -2 -8 8. Dimensions in inches

A: The area is divided into the standard areas as shown below.

Q: 17. COMPLETE THE FOLLOWING INSERT CODE IN INCHES: MG 43 18. COMPLETE THE FOLLOWING INSERT CODE IN…

A: 17. It is made up of  CNMG432       1/2" inner circle , 1/32" corner circle and 80°  Diamond woth 0°…

Q: A clockwise couple M = 4.5 N m is resisted by the shaft of the electric motor. (Figure 1) Part A…

A: Given: The moment M is 4.5 N.m. Consider the figure,

Q: XXXX W₂ W₁ Which of the following most nearly gives the external degree of indeterminacy? 2 4 O 1

A:

Q: Determine how far is the centroid of the given cross section above the base. 6-504 2-50" 9.0" 6.5"…

A:

Q: Assignm R= Station 18+26 18+00 17+00 16+00 15+68 3: For Arc 0 Deflection Angle (DMS) 0°0'0" Chord…

A: Horizontal Curve :  In order to transition between two tangent strips of road, a horizontal curve is…

Q: hat about pin d?

A: We know that Forces acting at Joint D are shown in figure below Forces moving away from joints are…

Q: What are the commonly available switch actions?

A: Commonly available switch actions? ON-OFF, SPST. SPST = Single Pole, Single Throw.  (ON)-OFF,…

Q: Figure 2. Inside perimeter Outside perimeter Centreline

A: Inside perimeter :Length×2+Breadth×2+2×2'+3'24'3''×2+12'×2+2×2'+3'=79'6''

Q: -0129 -077 R26

A:

Q: If Ax B = = A.B then the angle between A and B will be %3D a) п b) π/2 ) π/3 TE e) None of the above…

A: To find angle between A and B

Q: The 4th root of 81

A: Answer : 3

Q: Explain why wx = 2/3(9-x)

A: Given:Required:To explain loading intensity for 6<x<9

Types of Composite

Composite materials are formed by merging two components that have different chemical and physical properties. The merged output is termed as a composite, whose properties are completely different from the individual components. Composite materials also have better strength than the individual components.Composite materials usually have two main parts, reinforcement material, and matrix material. The matrix material acts as a binder and surrounds the fiber of another material that bears a much higher strength. This material is known as the reinforcement material. The matrix materials are usually high-strength additives resins, while the fibers of the reinforced material can be random, oriented, and in a mat format.Composite materials are also known as fiber-reinforced composite polymers because they are composed of the polymer matrix which is reinforced to laboratory-created fibers or naturally occurring fibers, such as glass fibers, carbon fibers, or aramid fibers. Under the application of external loads, the matrix material absorbs and transfers the loads to the fibers, these fibers in return provide good compressive strength, tensile strength, and stiffness to the fiber-reinforced composite materials.Depending upon the matrix and the reinforcement material, different properties can be induced to the fiber-reinforced composite materials, including good corrosion resistance properties. The most common matrix material is the resin while the glass fibers act as the reinforcement material. Strong fibers provide strength and stiffness to the composite materials while, a soft and flexible resin provides shape to the composite materials.