Compute complex power of each element. Find the average power supplied by the voltage source to the load. vs(1) R=1022 L = 20 mH ww UR(1) i(t) V₁ = UL (1) vc(t)C= 100μF = 100 cos 1000t V =100/0°

Q: Q) The frequency is relating to time period--- Square proportional. O Not related. Directly…

A: In this question Choose the correct options What is relation between frequency and time period.

Q: If the secondary side of a dual-voltage single phase transformer, as per figure 1,  were to be…

A: The secondary side of a dual-voltage single phase transformer, as per the figure given in  the…

Q: difference between measurement uncertanty and measurement error

A: Given : Need to find the difference between measurement error and uncertainty.

Q: What is the difference between the pins under number 1 and the pins under number 4, and mention when…

A: The difference between pin 1 and pin 4 is the transmitting ability (information) to external…

Q: define the fake resistance

A: Fake resistance has property of some electrical circuit s and devices in which an increase in…

Q: What is the FOA ratings in MVA

A:

Q: When the load of a voltage multiplier is too small, __." Choices: the output voltage is unaffected…

A: Voltage multiplier is the circuit which is used to give high dc value of voltage at the output…

Q: Task Sketch a graph of V₁ vs V

A:

Q: In FET, what is the value for when Ip=lpss/2? [Approximate time to answer: 2 Minutes.] O gmo/2 O 3…

A: solve for transconductance

Q: Which type of levels are the most commonly employed today. O a. Dumpy levels O b. Automatic levels…

A: To do:We have to select the right option from given four different options for type of levels that…

Q: 1. Differentiate an Elemental Semiconductor from a Compound Semiconductor. Explain one advantage of…

A: Semiconductor- semiconductor are the element whose conductivity lies between conductivity of…

Q: Did you meet at the college .A a lot of .B anybody .C few .D

A: Given: Did you meet _______ at the college

Q: Ota the cucut beluu, asoume vact) = lewcus (500t) and tL isa (OPF capacitorin series with a lwe…

A:

Q: What is HT supply?

A: What is HT supply?

Q: differentiate between overhead service connection and under ground service connection with sketch

A: Overhead Service Connection:- Electric locomotives, trolleybuses, and trams receive their electrical…

Q: Refer to the National Electrical Code or the working drawings when necessary. Where applicable,…

A: We are authorized to answer one question at a time, since you have not mentioned question you are…

Q: Assume that the collector current changes from 2.5mA to a new level of 3mA. Determine the magnitude…

A: Given thatcollector current change from 2.5mA to 3mAfind magnitude of IC change %

Q: True or False: We can use BLOG term in 66 blocks to remember the wire order, and remember to start…

A:

Q: Skin effect impact O a. the frequency of the TL O b. the current of the TL Oc. all of the other…

A: In AC power systems the skin effect or skin effect losses are referread as the losses due to flow of…

Q: For the circuit shown in the figure below, com

A:

Q: TRUE OR FALSE QUESTION: Explicit Time integration is much stable than Implicit Time integration?…

A: Explicit time integration:- Explicit time integration method integrates constant accelerations…

Q: Determine the take-up and measurement to your mark for each of the following. Length EMT Size…

A: According to the question, we need to calculate take-up and mark for the given EMT size.

Q: For The Volfage-divider bias configurafion of the hgure Shown below, determine: Vc ,VE B IBQ. I ca,…

A:

Q: What happens to the system voltage gain if the middle configuration is removed? Are there any…

A: BJT and MOSFET are the class of transistors used in analog electronics. They are widely used…

Q: 3kN R2 6 k

A: "Since you have posted a multiple question we will solve first question for you .To get remaining…

Q: 2. Explain over modulation.

A:

Q: Due to the effect of the resistance of the cable connected to RTD, two-wire cables up to ……. meters…

A: c) 50-195

Q: inm do A ☺ 52

A: From the mesh Analysis

Q: How much demand factor is considered in the first 3000VA of hospital occupancy? 40% 35% 100% 20%

A: Demand factor:- It is defined as the ratio of maximum demand to the connected load on the system. It…

Q: The registers are involves in Indirect Cycle are: MAR, MBR O MAR, MBR, IR MAR, MBR, Control unit.…

A: After the fetch cycle is completed, the source operands are fetched and the indirect cycle occurs…

Q: Qg:- for dhe numbers below 1. (1011 o1) 2 ( loo1)e Find s- O muttipliantion of the two numbert 2…

A:

Q: In a step-up transformer, the turn ratio is 1: 20. The resistance of 100 2 connected across the…

A: Given information is shown below:To find:

Q: 110 About indistrial piping WHY IS THE ASME 31.3 ALLOWABLE VOLTAGE A COMBINED VOLTAGE?

A: According to the question, WHY IS THE ASME 31.3 ALLOWABLE VOLTAGE A COMBINED VOLTAGE?

Q: Convert below base20 number into base3 number  (7AD)base 20 Please provide answer as soon as…

A:

Q: what is the receptacle load (after demand factors) for an office building with 250 receptacle…

A: Receptacle loads are described as equipment loads that are generally served by electrical…

Q: Speed control of slipring Induction Motor. MCB Instruction SN Ammeter WattMeter Speed 1 2.6 2 2.9 3…

A: Induction motor- The induction motor is define as the AC operated electric motor. In which the…

Q: Remember to put no space in between characters. If the final answer is a whole number, put no…

A: Note: As per our policy, I have answered the first three subquestions. Given data: C1=2.5 FC2=1.5…

Digital Integrated Circuit Design

Digital IC design is a procedural interaction that involves converting determinations and highlights into computerized blocks, which are then further transformed into basic circuits. A significant number of the imperatives related with advanced IC plan come from the foundry cycle and innovative restrictions.