To approveD.Compressive stress can be defined or described as an internal force in a matefa26.resisting aA. shearing load.B. pulling load.C. pulling and shearing load.D. pushing load.27.The following material is being order as the most hardiness material.A. Glass, Lead, Aluminum, Gray ironB. Gray iron, Aluminum, Glass, LeadC. Aluminum, Gray iron, Glass, LeadD. Glass, Grày iron, Aluminum, Lead28.The edges of a cast iron block weighing 32 kg were rounded off with a mil uthe block was reweighed, it was found to weigh only 29.5 kg. What percentage oforiginal cast iron block was lost?A.7.8%8.5%4%D. 2.5%В.С.oil vve

Note: As per the Bartleby guidelines, only one question can be answered at a time. Therefore, please…

Answered: Compressive stress can be defined or…

Compressive stress can be defined or described as an internal force in a mate 26. resisting a ... A. shearing load. B. pulling load. C. pulling and shearing load. D. pushing load.

Welding: Principles and Applications (MindTap Course List)

8th Edition

ISBN:9781305494695

Author:Larry Jeffus

Publisher:Larry Jeffus

Chapter25: Testing And Inspection

Section: Chapter Questions

Problem 39R: What information does a hardness test reveal?

See similar textbooks

Similar questions

Millimeter 17. Which part of the marking gauge is used to mark lines on wood? To measure the ductility of weld metal b. To test the skill of a welder To perform a non-destructive test d. To approve welds to certain standards a. C. 18. Compressive stress can be defined or described 2s an internal force in a material resisting a. a pulling load. b. shearing load. pulling and shearing load. d. pushing.load. • C. 19. Which plane more suitable for further smoothing a planed surface? Router plane. b. Trying plane. c. Smoothing plane. a. 20. Which one of the following is gives the name of the screw? a. Siot. b. Thread. Head. d. Shank. C. 21. How to hold the hammer handle while driving the naii? Middle of the handle. * b. Anywhere in length of the handle. C. Near the hammer head of the handle. End of the handle a. USF ال لجنة العلمية d. File is
All three parts please
Please help. Do not just guess. Prove your answer. I will give a good feedback.
2) Which one of the following material is having high toughness a. High carbon steel b. Medium carbon steel c. Ductile cast iron d. White cast iron
15- Which one of the following material is having high toughness a. High carbon steel b. Ductile cast iron c. Medium carbon steel d. White cast iron
20- Vickers Hardness Number (HV) value is directly proportional to a. Shape of indenter b. Indentation mean diagonal c. All of the above d. Force applied
32. Fine-grained materials have stress-hardening properties. a. True b. False
_____ is an example for indirect stress Select one: a. Shear b. Bending c. Tensile d. Compression
Q1: Select the correct answer. up to A. Resilience is the energy absorbed by the material a. yield. b. ultimate sensile stress. c. fracture. B. The grain boundaries are a. less chemically active than grains themselves. b. the regions of orientation mismatch of the neighbouring grains. c. classified as linear defects. C. All polycrystalline materials are considered as isotropic because a) they have crystallographic direction-mechanical properties independence relation b) all the crystals' orientations are the same c) the random direction of many grains cancels the anisotropic effect D. Dislocations slip process in metallic crystalline materials a) is essential to explain why the metals exhibit much lower strength than that theoretically predicted based on metallic bonding. b) makes metals and alloys brittle. c) cannot be used to control the mechanical properties of metallic materials E. The atomic stacking ABCABCABC is for d) FCC crystal structure e) BCC crystal structure f) HCP crystal…
Any steel used as a tool may be technically classified as a tool steel. However, the term "tool steel" is usually restricted to high-quality specialty steels used for cutting or forming purposes. True False Both Ferritic and Martensitic stainless steels belong to the AISI 400 series. Ferritic stainless steels are heat-treatable grades and martensitic stainless steels can only be strain hardened to improve their mechanical properties. True False The RIM (Reaction Injection Molding) process does not require the plastic materials to be heated before molding. True False An aluminum alloy designated as 3003-H16 aluminum means the following: 3XXX aluminum-manganese alloy, which has not been modified, specific alloy 03 in the alloy series, strain hardened only, with a 3/4 hard temper. True False Titanium is extensively used for jet engine components (rotors, fins, and compressor parts) and other aerospace parts because it is as strong as aluminum and 45 percent…
Stainless steel 18. These are used in wide variety of applications owing to the properties like good fluidity, ease of casting, low shrinkage, excellent machinability, wear resistance and damping capacity. * O Cast irons Copper alloys O silver alloys O Steels 16. The condition after more than 500 years. tubing used in water plumbing in pyramids was found in serviceable
PLEASE ANSWER ASAP! RATE WILL BE GIVEN! NO LONG EXPLANATION NEEDED! STRENGTH OF MATERIALS (MULTIPLE CHOICE) Which of the following is NOT TRUE with respect to the Elastic Transverse Shear Formula? a.Transverse shear stress is maximum at the top fiber of the cross-section. b.Transverse shear stress is zero at the neutral axis. c.The value of Q is maximum at the neutral axis. d.The maximum transverse shear stress is maximum where the ratio (Q/t) is maximum e.The value of Q at the bottom fiber is maximum