Completely solve and box the final answers. Please write legibly.Complete the table given below by finding the reaction forces and all the force members with the corresponding types of force (tension or compression) for the given truss. Use METHOD OF JOINTS in analyzing the given structure. Complete the following table based on your solutions and answers in Question 1.Table of Answers in Question 1REACTIONS/ FORCE MEMBERSMAGNITUDE, kNTYPE OF FORCEReaction at A (horizontal)Reaction at A (vertical)Reaction atDАВAEBCВЕСЕDECD |5 kN7 kNB10 kN6060E4 m4 m

Answered: Image /qna-images/answer/cc9dc042-e19a-40d2-b738-3f2f6a106b77.jpg

Completely solve and box the final answers. Please write legibly. Complete the table given below by finding the reaction forces and all the force members with the corresponding types of force (tension or compression) for the given truss. Use METHOD OF JOINTS in analyzing the given structure.

Completely solve and box the final answers. Please write legibly. Complete the table given below by finding the reaction forces and all the force members with the corresponding types of force (tension or compression) for the given truss. Use METHOD OF JOINTS in analyzing the given structure.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Problem 6.42 Consider the truss (Figure 1). Suppose that F = 14.5 kN Figure 1 4 kN of 1 6 kN H B m G 2 m 9 KN C -1.5 m 1.5 m 1.5 m 1.5 m 1 m D > 6 kN E Part A Determine the force in member BC. State if this member is in tension or compression. Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive value in the case of tension. FBC = Submit Part B FHC = D μA Submit Value My Answers Give Up Determine the force in member HC. State if this member is in tension or compression. Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive value in the case of tension. Units μA Value Units ? My Answers Give Up ? Part C Determine the force in member HG. State if this member is in tension or compression. Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of…
Rigid bar ABCD is loaded and supported as shown. Steel [E = 28400 ksi] bars (1) and (2) are unstressed before the load P is applied. Bar (1) has a cross-sectional area of 0.82 in.² and bar (2) has a cross-sectional area of 0.41 in.². After load P is applied, the strain in bar (1) is found to be 700 μe. Assume L₁=69 in., L₂-89 in., a=34 in., b=33 in., and c-37 in. Determine: (a) the stresses in bars (1) and (2). (b) the vertical deflection VD of point D on the rigid bar. (c) the load P. A Answers: (a) 0₁ = (b) VD = (c) P= i i i L₁ a (1) B L2 b ksi, 0₂ = in. kips. (2) C i D P ksi.
The section of a thick beam has the dimensions shown in the figure below. Calculate the section properties lz, ly and Izy (Izy = product of inertia) referred to horizontal and vertical axes through the centroid of the section. Refer to Section 6 in your notes for properties of planed sections. Also determine the direct stress at the point A due to a bending moment My = 55 Nm. (Hint: use Page 7-9 in your notes) Ay A 5 mm 20 mm G 5 mm 5 mm 10 mm
2. Determine the normal stress in members BD, AC, and BC in the truss shown. The cross- sectional area of each member is 1500 mm2. Indicate whether the stresses are tensile (T) or compressive (C). Use 2 decimal places in every solved value. 10 m 10 m 10 m K 6 т H 6 т 15° 15° 50 kN 40 kN E F 6 т C D б т A B
Engineering Mechanics DETERMINE THE INTERNAL FORCE OF MEMBER DE FROM THE FIGURE BELOW. Note: for compression, include a negative sign ( - ) and for tension, type answer as is. Use four (4) decimal places during computation and two (2) decimal places for the final answer.
Determine the normal stress in members BD, AC, and BCin the truss shown. The cross-sectional area of each member is 1500mm2. Indicate whether the stresses are tensile (T) or compressive (C). Use 2 decimal places in every solved value.
A wooden beam is fabricated from one (2 x 10 in) and two (2 x 4 in) pieces of dimension lumber to form the l-beam cross section shown in Figure. The flanges of the beam are fastened to the web with nails that can safely transmit a force of (120 Ib) in direct shear. If the beam is subjected to a shear force of (500 Ib), determine the maximum the maximum shear stress in the l-beam. Use l = 748 in4 4 in. 2 in. 2 in. 10 in. 2 in. Nails 50.3 psi O 24.4 psi 45.3 psi O 12.0 psi O
Consider the truss shown in (Figure 1). Suppose that F1 = 60 kN and F2 = 20 kN . Part A Determine the force in member ED of the truss, and state if the member is in tension or compression. Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive value in the case of tension. Part B Determine the force in member EH of the truss, and state if the member is in tension or compression. Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive value in the case of tension. Part C Determine the force in member GH of the truss, and state if the member is in tension or compression. Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive value in the case of tension.
Consider the truss shown in (Figure 1). Suppose that F = 12 kN. gure B C D 12 m, 6 @ 2 m E F 3 m Part A Determine the force in member CD and state if this member is in tension or compression. Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive value in the case of tension. FCD = Submit Part B FCJ = Submit __ Part C μA Value Request Answer Determine the force in member CJ and state if this member is in tension or compression. Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive value in the case of tension. μA Value Units Request Answer ? Units ? Determine the force in member KJ and state if this member is in tension or compression. Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive value in the case of tension.
Determine the member stresses in members AB, AC, AD, BC, and BD if the cross-sectional area for all members is 800 mm². Note: You may use any method 3 m ון 2 - 3 m 4 m 5 m 6 kN Situation 4: Terminologies 1. A structural element that carries a load that is applied transverse (perpendicular) to its length and the top fibers are in compression; the bottom fibers are in tension. 2. A structural element that is composed of smaller structural members typically configured in triangular arrangements. 3. Codes that specify combinations of loads that must be considered in the design of structures in the Philippines? 4. How many equations of equilibrium are there in space structures? 5. These are the forces exerted by supports on the structure and tend to prevent its motion and keep it in equilibrium. 6. The internal force in the direction of or parallel to the centroidal axis of the beam 7. The internal force in the direction perpendicular to the centroidal axis
Determine the force in each member of the loaded truss. Explain why knowledge of the lengths of the members is unnecessary. 3010 lb Answers: AB= AC = BC= 35° i i i B 64° C lb lb lb
The figure shows a frame structure subjected to a horizontal load P = 500 lbs at pin C. The pins at B, C, and D apply axial loads to members BD and CD. If the stresses in BD and CD are limited to σ1 = 1200 psi and σ2 = 820 psi respectively, what should be the cross sections of the two members (in inches)? Note: Draw the Free Body Diagram, include the units/dimensions, use the proper formula and round-off all the answers and final answers to 3 decimal places.