Combined stresses: tutorial question 1¹ The tank show opposite has an inner radius of 600 mm and a thickness of 12 mm. It is filled to the top with water having a specific weight of yw = 10 kN/m³. If it is made of steel having a specific weight of Yst = 78 kN/m³, determine the state of stress at point A. The tank is open at the top. Internal loadings. 1m 600 mm = 12:

Q: c) Sample of an aluminum alloy has a tensile strength of 175 MPa, What will be the maximum force…

A:

Q: Table 3 shows the fatigue data for a ductile cast iron to be used for an automobile axle that…

A: Given Data for ductile Cast iron Stress Ampitude (Mpa) Cycles to failure 740 1*101 604.8…

Q: (Textbook: page 51, problem 12) How can machinery parts and pipeline welds be tested for flaws…

A: THESE TESTS LIKE X-RAYS AND HYDROSTATIC TESTS ARE NON DESTRUCTIVE TESTS. THE BASIC GOAL IS TO…

Q: -0.749 diom -0.561 diam -24 UNF-2A-

A: Based on the information provided, there are two components that failed: the M24 engine mounting…

Q: When performing a quench to cool a product, the quench rate affects the outcome of the process. TRUE…

A: In general, a high quenching cooling rate may result in the maximum hardness and the best…

Q: Which of the following describes the crystal structure of steel? Group of answer choices Steel is a…

A: The iron-carbon diagram is a graphical representation of phase changes occurring in carbon content…

Q: How is ductile iron different from malleable iron?

A: This question is based on the concept of types of Iron.

Q: I. In a few words or in a single short sentence explain why it is easier to deform a piece of…

A: Explanation:  (i) Aluminum is the more ductile as compare to steel. Aluminum has not yield points…

Q: Hello I have just a quick question I was wondering an expert could answer. Would you happen to know…

A: A BHN of 103.262 for an aluminum alloy suggests that it has a relatively moderate hardness. However,…

Q: Most metallic materials with crystal structure display a sharp decline in impact energy when tested…

A: B.C.C is Body Centered Cubic crystal structure in which one atom is at centre of unit cell and…

Q: Why is knowing the maneuver speed so important?Describe the Ultimate Load Factor (ULF).Why is…

A: To find:Why is knowing the maneuver speed so important?Describe the Ultimate Load Factor (ULF).Why…

Q: The collar A, having a mass of 0.75 kg is attached to a spring having a stiffness of k = 260 N/m.…

A: Given data  Mass of collar = 0.75 kg Spring constant = 260 N/m Find the speed of collar and normal…

Q: what is the Mohr Circle ?

A: Solution:   Mohr Circle with a proper example is explained below:

Q: A nodukat or ductile cast-iron is identified by the ASTM with a three part grade designation. And…

A: The ASTM designation of ductile cast iron is denoted by three numbers separated by a dash. The first…

Q: What do the holes and sharp transitions at a cross-section create?

A: Stress concentration: A stress concentration is defined as a phenomenon at a location where the…

Q: How does the Deformation of a body occur?

A: Deformation: Whenever a body is subjected to a change in its shape size from its original shape and…

Q: The properties of materials can be classified into the following categories: Mechanical Physical…

A: Properties of Material: Each material have different properties according to the uses and also…

Q: Explain the following with appropriate examples (at least 2 examples) 1. Grubler's criterion. 2.…

A: The Grubler's criterion gives the number of degrees of freedom of a mechanism involving links and…

Q: How can the change in length of a statically determinate member be easily calculated?

A: statically determinate member:     Reactions and internal forces cannot be found by statics alone…

Q: Explain the term availability and perform simple calculations.

A: The availability of a system states as the maximum useful work that received in a process in which a…

Pressure Vessels

The term pressure vessel refers to a closed container that contains gas or liquid at a different pressure than environment pressure. The pressure vessels have a wide scale of applications in our day-to-day lives and other industrial places. Some common examples of pressure vessels are gas cylinders, autoclaves, compressor vessels, etc.