Answered: Cold working of a metal results in:…

Cold working of a metal results in: (This question has only one correct answer) а. Increased ductility O b. Lower yield strength С. Reduced elastic modulus d. Higher yield strength

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The stresses in the deformed regions are relieved during recovery, which occurs a. above the recrystallization temperature O b. below the recrystallization temperature O c. above the melting point O d. in the room temperature O e. in all temperature ranges
What is the effect of strain hardening on the material?
The minimum yield strength for iron with an average grain size of 6x10^-2 mm is 135 MPa, this increases to 260 MPa when the average grain size is reduced to 8x10^-3 mm.What must the average grain size be to achieve a yield strength of 205 MPa.
sketch
98 Z 161423820785837... -> Choose the correct answer for the following: 1- Cast iron the refined form of ? a- Pig iron b- carbon C- molybdenum 2- Proof stress is used when the material ? a- Don't have clear yield point in stress-strain diagram. b- Have clear yield point. C- Have no elasticity 3- Ductile material ? a- Have elongation before failure. b- Doesn't have elongation before failure. c- When failure the section of failure flat. 4- Compression test is the opposite of tensile test ? a- According to direction of applied load. b- Is the same direction of applied load with tensile test. c- Compression test used with metallic materials to determincition Its properties. 5- Impact test ? a- Used to measuring the stress. b- Used to measuring the energy absorbed in bending or breaking the specimen. c- Used to measuring the plasticity. 6- Vacancy diffusion this tape occurs in all metals or alloys a- With Fcc only types of crystal structures b- With Fcc Bcc and Hcp types of crystal…
Help with this 2 questions ..kindly note I have attached 2 questions
Figure shows a diagram from an impact strength test of metals that have three different crystal structures.a) What type of crystal structures do the curves (I), (II) and (III) represent? b) why won't the metals in curve (I) have a marked transition temperature?
Which method do we use to monitor dislocation movements in tensile testing? How monitoring is done in this method, explain the working mechanism of the system in detail.
The figure shows two work pieces of steel of 0.15 %C and 1.2 %C with different dimensions. Compare between them regarding:- 1- The existed phases and the expected mechanical properties of each. 2- Give 5 important applications for each alloy. 3- The stages of Normalizing treatments for each one. 900 800 1 Aj = 727°C 0.0218 0.77 700 Dimensions of (1.5*1.5*1.5) inch Dimensions of (1*1*1) inch 0.2 0.4 0.6 0.8 1.0 1.2 1.4 6.67 Weight percent carbon Temperature ("C)
(2) Consider a homogeneous structure made out of metal subjected to homogeneous boundary conditions t = σn. For o corresponding to uniaxial, biaxial and shear stress state, calculate the stress at which the material yields.
Which curve shown below (A or B) is for a BCC metal and why? A В Brittle + More Ductile Temperature Duclile-o-britte transilion temperalure Impact Energy
Q3 contd. (d) The yield strength values of pure aluminium (Al) and pure copper (Cu) are 25 MPa and 20 MPa, respectively; whereas the yield strength values of cold rolled Al-Mn-Mg alloy and cast 60-40 Brass (60% Cu, 40% Zn) are 200 MPa and 105 MPa, respectively. With aid of schematics, explain the main mechanisms account for the increases in the strengths. (e) A cylindrical tie rod with a diameter of 18.4 mm is subjected to cyclic loading. The stress range is +/- 200 kN. Figure Q3.3 shows the S-N curve of the material of which the rod is made, how many cycles will this rod survive? Stress amplitude O₂ (MPa) 1500 1400 1300 1200 1100 1000 900 800 700 600 500 400 10² 10³ 104 4340 low-alloy steel Stress ratio = -1 Fig. Q3.3 105 106 Number of cycles to failure, Nf 107 108