Cogeneration is often used where a steam supply is needed for industrial process energy. Assume a supply of 5 kg/s steam at 0.5 MPa is needed. Rather than generating this from a pump and boiler, the setup in below. is used so the supply is extracted from the high-pressure turbine. Find the power the turbine now cogenerates in this process. 1 2 3 НР LP

Cogeneration is often used where a steam supply is needed for industrial process energy. Assume a supply of 5 kg/s steam at 0.5 MPa is needed. Rather than generating this from a pump and boiler, the setup in below. is used so the supply is extracted from the high-pressure turbine. Find the power the turbine now cogenerates in this process. 1 2 3 НР LP

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The cycle comes with a net power cycle of 25.40 kW. The heat that goes out is 42.30 kW. Find the efficiency of the cycle?
superheated steam enters the turbine at 873K and 18MPA. Find the isentropic efficiency of the following turbine. Also find T2 and turbine actual power output. The flow rate is 10 kg/s. It exists as saturated vapor at 393K. hint: the isentropic case should exit as high quality mixed phase.
A rankine cycle with water superheats to 500.546oC at 3.1546 Mpa in the boiler and the condenser operates at 100.546oC. All the components are ideal except the turbine which has an exit state measured to be saturated vapor at 100.546oC. Find the cycle efficiency with a) an ideal turbine and b) the actual turbine. Draw the schematic diagram and T-s diagram.
1.) A Steam power plant operates using the ideal Rankine Cycle where steam initially enters the turbine at 5.0 MPa and 400C then after expanding, it condenses at 7 kPa and exits as saturated liquid. Draw the TS diagram, find the thermal efficiency, and steam rate.
A Camot engine operates between 12000F and 1000F and rejects 40 Btu to the low temperature heat reservoir. Find the net work.
If the Mean Effective Pressure (MEP) is the ratio of the net work and the volume displaced, find the MEP per kg of air in an Otto Cycle with initial conditions of 0.1 MPa, 306K; rk is ten and max temp is 3021R.
Steam enters the turbine at 10 MN/m2and 450oC. The steam expanded in the turbine down to the condenser pressure of 20 kN/m2. The condensate leaving the condenser is pumped to the boiler pressure directly. The turbine has an isentropic efficiency of 89%, and the mass of steam generated in the boiler is 5 kg/s. Find: Cycle thermal efficiency. Plant power output.Neglect the pump work and draw the cycle on a T – s diagram. Hint: 1 MN/m2= 10 bar
Steam at 6.2 MPa and 480 deg. C is received by a regenerative engine with ideal conditions and in an ideal cycle. Extractions for feedwater heating occurs at 3 MPa and again at 1.4 MPa, with the remaining steam expanding to 0.0065 MPа. What is the engine work in KW
need correct and urgent
Please show step by step solution not just answers and how each value is derived dont just mention from a table becuase i cant fnd it, if mentioned please display it.
A heat pump operates with Qin = 100kJ and Qout=250KJ. The cycle work is O 150kJ O -150kJ 350kJ -350kJ O Such cycle is impossible.
10 0.9967. Ans. H.W 2 A smaller power plant produces steam at 3 MPa, 600 C, in the boiler. It keeps the condenser at 45 C by the transfer of 10MW out as heat transfer. The first turbine section expands to 500 kPa, and then flow is reheated followed by the expansion in the low-pressure turbine. Find the reheat temperature so that the turbine output is saturated vapor. For this reheat, find the total turbine power output and the boiler heat transfer. Answer. (Reheat temperature= 529°C , total turbine power output= 6487 kW, the boiler heat transfer= 16 475 kW)