12 A 1000 kVA, 3000V, 60 Hz, 3phase, Y-connected alternator has anarmature effective resistance of 0.20 ohm. A field current of 40ACO212.CO3CO4produces a short circuit of 200A and an open circuit emf of 1040Vbetween lines. Determine the full load percent regulation at 0.80lagging power factor.A. 24.3%C. 26.5%B. 18.7%D. 13.5%

CO2 12. A 1000 kVA, 3000V, 60 Hz, 3phase, Y-connected alternator has an CO3 armature effective resistance of 0.20 ohm. A field current of 40A CO4 produces a short circuit of 2O0A and an open circuit emf of 1040V between lines. Determine the full load percent regulation at 0.80 lagging power factor. A. 24.3% C. 26.5% B. 18.7% P. 13.5%

CO2 12. A 1000 kVA, 3000V, 60 Hz, 3phase, Y-connected alternator has an CO3 armature effective resistance of 0.20 ohm. A field current of 40A CO4 produces a short circuit of 2O0A and an open circuit emf of 1040V between lines. Determine the full load percent regulation at 0.80 lagging power factor. A. 24.3% C. 26.5% B. 18.7% P. 13.5%

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

12 - How to calculate the impedance of a coil?A) It is the difference between ohmic resistance and inductive resistance.B) It is the ratio of ohmic resistance to inductive resistance.C) It is the vectorial sum of ohmic and inductive resistance.D) It is the algebraic sum of ohmic and inductive resistance.E) It is the ratio of inductive resistance to ohmic resistance.
Power systems quality
When you are as an engineer, when will you decide to use Voltage-Shunt N.F.B? 18- 17- When you are as an engineer, when will you decide to use Voltage-Series N.F.B? 19- When you are as an engineer, when will you decide to use Current-Shunt N.F.B? 20- When you are as an engineer, when will you decide to use Current-Series N.F.B?
Write down at least three reasons which cause difference between R1 (R2) and R = Vmes/imes values in the below table?
Q1. Give the definition of: a) Resistance: b) Reactance: c) Phasor diagram: d) What is the unit of reactance?
use junction and loop rule also use gauss elimination
Quiq plz
Determine Vo, given Vin=25V, V1= - 8V, R1=3k0, R2=5kO For Ge Vy = 0.3 V For Si Vr = 0.7 V K Ge R1 Si V. in Vo R Lütfen birini seçin: a.12.7V b.23.91V c.9.47V d.4.58V e.18.64V
kindly give short and accurate answer. thanks.the course is power transmission system
PLEASE LABEL AND DESCRIBE DIAGRAM
two resistor in series connection, 20k ohms and 50 ohms respectively are at ambient temperature generates 2.16uV noise voltage, calculate the equivalent noise voltage if these two resistor are to be connected in series a. 987.82uV b. 975.79nV c. 952.16nV d. 440.82nV if the answer is not in the choices write it
Node2: Node1 www..