A pressure-vessel head is fabricated by gluing the circular plate to the end of the vessel as shown in the figure. If the vessel sustains an internal pressure of 480KPA, determine the average shear stress in the glue 450 mm 10 mm 20 mm and the state of stress in the wall of the vessel.

A pressure-vessel head is fabricated by gluing the circular plate to the end of the vessel as shown in the figure. If the vessel sustains an internal pressure of 480KPA, determine the average shear stress in the glue 450 mm 10 mm 20 mm and the state of stress in the wall of the vessel.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

5. The aluminum alloy bar has a circular cross section with 20-mm diameter and a shear modulus of 28 GPa. What is the magnitude of the maximum shear stress in the bar due to the uniformly distributed torque? y 8.5 kN-m/m 120 mm
pls help me answer my homework. thank you.
The bronze bar 3.00 m long with a cross-sectional area of 350 mm is placed between two rigid walls. At a temperature of – 20 °C, there is a gap of 2.20 mm. Find the temperature at which the compressive stress in the bar will be 30 MPa. Use a = 18x10/°C and E = 80 GPa. L = 3.0 m 2.20 mm
PROBLEM 1 A circular aluminum tube of L=600mm is loaded in by compressive forces at its ends. The outside and inside diameters are 75mm and 63mm respectively. A strain gage is placed on the outside of the tube to measure nomal strains in the longitudinal direction. E=73 GPa and Poisson's is 0.33. a. If the normal stress in the tube is 57 MPa, what is the load P? b. if the strain is 781 X 10-6, what is the shortening of the tube? What is the percent change in its cross-sectional area.
Q2/ the structure shown below, support from fix at the left , the max normal at bronze =200 MPA, Find area of bronze , normal stress at both steel and aluminum 10 KN Steel Aluminum, A= 100mm? A=200mm? Bronze, A=? 8 KN 5 KN 5 KN 3m 2m 1 m
use mhors circle a.What is the value of the minimum stress in psf? b.What is the value of the normal stress acting at the plane AB in psf? c.What is the value of the shear stress acting at the plane AB in psf?
Strain gage on the surface of a thin-walled steel boiler as shown in the figureaffixed. With shape change meter εx = 500 (10-6A value of) was read. The inner diameter of the boiler 60Mm. The wall thickness of the boiler is 2mm E=200 GPa, υ=0.3 a)Calculate the stresses in the boiler b)Determine the internal pressure in the boiler
Axial loads are applied with rigid bearing plates to the solid cylindrical rods shown in the figure. One load of P=34 kips is applied to the assembly at A, two loads of Q=25 kips are applied at B, and two loads of R=37 kips are applied at C. The normal stress magnitude in aluminum rod (1) must be limited to 16 ksi. The normal stress magnitude in steel rod (2) must be limited to 32 ksi. The normal stress magnitude in brass rod (3) must be limited to 24 ksi. Determine the minimum diameter (in in rounded to the nearest thousandths) required for rod 2.
A square hollow bar having an outside dimension of 250 mm by 250 mm with 6 mm thick is to be replaced by a solid circular bar. a) Determine the required diameter of bar so that the maximum shear stress in the bar will not exceed the maximum shear stress in the tube. b) If the computed value of diameter in the previous question increase by 15%, what is the new shear stress of the circular bar? c) Determine the angle of twist in degrees of the tube if the length of the tube is 1m and the shear modulus is 80 GPa. Use T=14 kN-m.
2. A cylindrical pressure vessel is a fabrication from steel plating that fits to the following descriptions: Thickness = 25 mm Diameter = 500 mm Length = 2.5 m What maximum internal pressure can be applied if the longitudinal stress is limited to 160 MPa, and the circumferential stress to 80 MPa
Describe the construction process for over-excavation of a building:
answer pls in hand written solution