You are asked to design a Zener diode voltage regulator, as shown in Figure 1.e, tỏhave a stabilized voltage of 3.3 V across the load R. The Zener diode has aconstant voltage of 3.3 V when its current is more than a minimum current of 10mA and has negligible dynamic resistance. The load current changes between 0mA (open circuit) and 200 mA. The input voltage Vị is equal to 5 V.i)Choose the value of series resistance Rs to have stabilized voltage at theoutput at all conditions.ii)Calculate the maximum current in the diode and the resistor Rs. Based onthese values, choose the maximum power ratings of the diode and the resistorRsV,RLV.Rs.Figure 1.e.

Answered: Image /qna-images/answer/acacfce0-c2b4-48d9-9994-14d0c09c22ca.jpg

Choose the value of series resistance Rs to have stabilized voltage at the output at all conditions. Calculate the maximum current in the diode and the resistor Rs. Based on these values, choose the maximum power ratings of the diode and the resistor

Choose the value of series resistance Rs to have stabilized voltage at the output at all conditions. Calculate the maximum current in the diode and the resistor Rs. Based on these values, choose the maximum power ratings of the diode and the resistor

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Find the applied voltage on a forward biased diode if the current is 1mA and reverse saturation current is 10-10. Temperature is 25°C and takes ideality factor as 1.5.
For the circuits shown below using ideal diodes find the values of the labeled voltages and currents
Discuss the working principle of a diode and also the equivalent models of a diode.
There are two LEDs that can be used as a polarity detector. Apply a positive source voltage and a green light results. Negative supplies result in a red light. Packages of such combinations are commercially available.Find the resistor R to ensure a current of 20 mA through the “on” diode for the configuration. Both diodes have a reverse breakdown voltage of 3 V and an average turn-on voltage of 2 V
Q-2: The input signal for half-wave rectifier is a.c. signal. The output of 800 load resistor is 50V d.c. voltage. The diode has a resistance of 25 Q. 5 a) Draw the graphs of input signal, diode signal and output signals. 20 b) Calculate the maximum voltage value for the input signal. AC Supply Diode www
ji
Assuming an ideal diode, sketch Vị, Và and ia for the half-wave rectifier below. The input is sinusoidal waveform with a frequency of 60 Hz. Also, determine and sketch V, and ir Ideal V-2 V 2.2 ka R 6.8 ka
Explain the importance of the Volt-Ampere Characteristics of P-N Diode
B. For the given waveform illustrated below, design a suitable circuit to obtain an output waveform from a sinusoidal Input of peak voltage 20 V. Hint. Select the types of diode as per your design 9.6 V Vot - 5. 2 V
Sketch the I-V characteristic curve for a real diode and label the main parameters and regions.
If the forward voltage drop on a diode is 780 mV, what is the current passing through it? Assume Is=4x10-16 A. O a. 6.412 mA O b. 5.343 mA O c. 4.275 mA O d. 7.481 mA O e. 3.206 mA
If the positive cycle of the waveform for full wave bridge rectifier , Which of the diodes is working . ..... ...... 10:1 120 V ms Output 60 Hz Puec) RL 220 N Dz 1000µF O D1, D2 D3, D2 D4, D2 D1, D4 not all above D1, D3 ellee