Choose the symbol for Fixed displacement single rotation compressor. Select one: Oa. O b Od.

Q: 1 F1 R1 M2 F2 R2 T1 T2 M3 F3 R3 T3 Tnet g)(N) (m) (Kg) (N) (m) (kg) (N) (N) (N.m) (N.m) (m) (N.m)…

A: here, take +ve torque in clockwise direction and -ve torqe in counter clock wise direction. from the…

Q: In falling ball viscometer experiment, the viscometer with a calibration factor K=0.3 is used to…

A: As per given question  Given data  Calibration factor=0.3 Density of oil=0.8 gr/cm^3 Density of ball…

Q: For a pump designation 1-x3-10 provided by the manufacture, find out the appropriate options for…

A:

Q: 2 Pressure gauge √x the hydraulic cycle in figure -consist of:7 5 6 X 3 Feed direction tank O…

A: ◆ Figure represented by no. 7 is tank. ◆ Therefore, correct option is (a).

Q: The figure below shows a schematic representation of compressor characteristics. What is the name…

A: Surge line is the name usually given to the uppermost line that contains point d only.

Q: Choose the symbol for check valve. Select one: d.

A: Check valves are the devices which allows the flow in only one direction. So, it is also known as…

Q: The 107-lb force P is applied to the 220-lb crate, which is stationary before the force is applied.…

A:

Q: Describe how the system works

A: A hydraulic system is a drive technique in which energy is transferred from an electric motor to…

Q: What power can be delivered by the turbine if its efficiency is 100%? The water flow rate is 0.01…

A:

Q: The rotary compressor gets its name from the fact that it has an off-center piston of rotor which…

A: This question is based on the concept of conpressors.

Q: The hydraulic cylinders is also known as

A: The hydraulic cylinder is a mechanical actuator which convert hydraulic energy  into the mechanical…

Q: In raising the pole for the position shown, the tension T in the cable must supply a moment about A…

A:

Q: Respond with TRUE if the symbol of the valve shown below is drawn corectly 2 3 IMM 4 15

A: Directional control valves: The valves which is used to allow fluid flow into different directions…

Q: Symbols Questions 1) Give the name of the following graphic symbols. P1 А В P T

A:

Q: Draw the graphic symbol for a two-position spring centered valve, a spring offset valve, an…

A: Valve symbols are used to develop hydraulic circuits with ease. They convey the necessary…

Q: Process control is generally referred as А. Process to enhance quality and quantity of final output…

A:

Q: In the figure, aluminum [E = 68 GPa] links (1) and (2) support rigid beam ABC. Link (1) has a…

A:

Q: State four espect to consider before selecting correct solvant

A:

Q: The capacity control for a screw compressor is accomplished with cylinder unloading true or false

A: A rotary compressor makes use of a rotary type displacement mechanism. These compressors are usually…

Q: Determine magnitude of compressor power.

A: Given; A standard vapor compression refrigration cycle operating with acondensing temperature…

Q: The spool in the given figure weighs 25 N, and its center of gravity is located at the geometric…

A: Given :  The weight of spool =25 N The weight of block =50 N Freebody diagram : Concept used :…

Q: Q2) Figure 2 shows a rope that is stretched between points A and C, there is mass m at point B.…

A: Given data: The magnitude of mass m = 20 kg. The height h = 2 m. The length d = 3 m. The angle…

Q: step of construction with sutible dimmenstion

A: To show the step of construction with sutible dimmenstion

Q: Add the correct numbers into text boxes to identify correct labelling of an SU carburettor. Tapered…

A: According to Su -Carburetor diagram labeling is done in below picture in step -2

Q: the engine rpm is measured by measuring the current of an alternrator, driven by the engine…

A: the engine rpm is measured by measuring the frequency of an alternrator, driven by the engine

Q: Which of the following won't have the same unit as the others? Select the correct response: Stress…

A: Stress:  It is the ratio of internal resistive force per unit area of any object is known as stress…

Q: Lhe Check valve.

A: Option d is the correct answer

Q: What would be done to increase the compressor speedon a belt-driven compressor?A. Decrease drive…

A: Typically, belt pulley systems are used to drive the generators that power the compressors. The size…

Q: Complete the schematic below to provide for the following: 1. Cylinders extend and retract together.…

A: Given : To find : Complete the diagram

Q: Choose the symbol for Fixed displacement single rotation compressor. Select one: O a. O b. Oc. d.

A: option a is only for fixed displacement compressor  option b is double rotation direction variable…

Q: A The symbol shown represents a: Normally Closed Pressure reducing valve. Normally Closed Pressure…

A: A pressure-reducing valve maintains lower pressure in branches of the hydraulic system. The system…

Q: NEED HELP WITH D THRUGH G

A: From the free body diagram, evaluate angle .Substitute .

Q: Two metal pipes AB and BC, each having a mass per unit length of 10 kg/m, are welded together at B…

A:

Q: When the car engine is cold, the main cooling cycle is blocked to allow good oil filtration. O…

A: Option (b) : Increase the engine temperature up to the optimum engine temperature.

Q: What size of receiver tank (gal) for a compressor is required if the pneumatic system is used to…

A: The objective of the question is to calculate the size of the receiver tank required for a…