Choose the correct answer for from the following sentences:1. The purpose of the microprocessor is to controlb. memoryc. processingd. tasksa. switches2. Which of the following instructions represents base-plus-index addressing mode?a. MOV AL,[BX] b. MOV AL,[SI] c. MOV AL,BX d. MOV AL,[BX+SI]3. The BIU pre-fetches the instruction from memory and store them inb. memoryc. stackd. queuea. register4. Which function is used to control the PWM (Pulse Width Modulation) on the Arduinooutput pin?a. digitalRead() b. analogRead() c. digitalWrite()5. Which port in the PIC16F877A has an 8 external interrupt inputs?a. Port-Ab. Port-Cc. Port-Bd. analogWrite()d. Port-Dd. 4KByte6. How much Flash EEPROM memory program found in the PIC16F877A microcontroller?a. 32KByteb. 16KBytec. 8KByte

Question 1:What is the purpose of the microprocessora. switchesb. memoryc. processingd. tasks✅…

Answered: Choose the correct answer for from the…

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter22: Sequence Control

Section: Chapter Questions

Problem 6SQ: Draw a symbol for a solid-state logic element AND.

See similar textbooks

Similar questions

Q3/(A) False OR True 1- A0-0 and BHE-1 are used as low bank-select signal: 2-AX is 2234 H after executing the following instruction: AAS. If AX-2234H. 3-IP register holds the offset address of the next instruction to be executed. 4- The XLAT instruction in 8086 assembly language is used to perform arithmetic operations between two memory operands. 5- Bus interface unit is responsible form
Solve in 8086 microprocessor
Can you give me a simple example of each mistake in the Emu8086 program? Registers should be of the same size. One way to reduce memory usage is to use AX or AL. Explain.
1.) A single instruction to clear the lower 4 bits of accumulator in 8085 alp is, a) XRI FOH b) XRI OFH c) ANI OFH d) ANI FO 2.) The status of Z, AC, CY flags after execution of following instructions are, MVI A, A9H MVI B, 57H ADD B HLT a) 0,1,1 b) 1,0,0 c) 1,1,1 d) 1,0,1 3.) Consider the loop: LXI H 000A MVI C OB LOOP: DCX H DCR C JNZ LOOP HLT This loop will be executed by: a) infinite times b) 11 time c) 10 times d) 1 time
The numbers from 0-9 and a no characters is the Basic 1 digit seven segment display * .can show False True In a (CA) method of 7 segments, the anodes of all the LED segments are * "connected to the logic "O False True Some times may run out of pins on your Arduino board and need to not extend it * .with shift registers True False
Consider the following instruction breakdown that decomposes an instruction into 4 parts: OPCODE DST SRC IMM OPCODE specifies the Operation's CODE. DST specifies a DeSTination register. SRC specifies a SouRCe register. IMM specifies a 2's complement value (that's IMMediately available as part of the instruction). Assume the architecture has 32-bit instructions, 231 opcodes, and 32 registers. A.) What is the minimum number of bits required to represent an OPCODE? 8 B.) What is the minimum number of bits required to represent a register? 3 C.) What is the maximum number of bits that can be used to represent the IMM value? D.) What is the largest positive value in base 10 that can represented by the IMM value?
New Solution
Implement 32-Bit MIPS Register file (Zero Register…etc) Information in Image
Assume register R0, R1 and R2 contain the value of 0x00000100, 0xAABB1122 and 0x00000102. ARM Cortex-M3 processor executes the instructions STR R1, [R0] and LDRB R1, [R2] in sequence. What is the content of register R1 if the storing mode of data in memory using Little Endian Mode? A. 0xAABB11BB B. 0xAABB1111 C. 0xAABB1122 D. 0x0000BBAA E. 0x00001122
Answer only 4 and 5
Given the memory content below, fill in the table below with the register values after the execution of 3 instructions starting at instruction at address 589. Consider the initial values PC=589 and AC=0006. (all values are in Hexadecimal). address Content 13C 025A 25A 0231 589 113C 58A 7200 58B 7020 Note that you need to fill 4 digits for AC, 3 for PC, and 1 for E. AC (in Hex)= EEBE PC (in Hex)= 58C E=
1.Without using the MUL instruction, give instructions that multiply register r4 by: a)128 b)253

SEE MORE QUESTIONS

Recommended textbooks for you

Electric Motor Control

Electrical Engineering

ISBN:

9781133702818

Author:

Herman

Publisher:

CENGAGE L

Electric Motor Control

Electrical Engineering

ISBN:

9781133702818

Author:

Herman

Publisher:

CENGAGE L

SEE MORE TEXTBOOKS